Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Hi,
I understand that the CoAP Client sample is configured for a public URL (californium.eclipseprojects.io) in the Kconfig file. I wanted to ask, how the KConfig file...
Hi,
I am trying to perform DFU over mesh network. I am following the steps as given in this .
I could achieve the steps from 1-6. But while running the command for Transferring...
Hi,
When running FreeRTOS I'm not able to use the NRF logger module once the task scheduler has started.
I have a low priority task that flushes the logs but whenever...
Context: nrf52840DK, s140, SDK 17.0.2
Hi,
I need to oversample a few ADC pins with burst enabled at roughly the same time periodically: e.g. oversampling 4 separate inputs...
Hello,
I have nrf52832 dev kit and the device. I try to make smaller code size and setup Optimization Level 2 for size.
BLE works, but when connect by NRF connect and...
Hi,
I am currently developing a product which is supplied with battries (chip is nRF52810). Under normal conditions, the product goes into system OFF mode in standby, it...
Hi,
I'm testing a custom board, based on nrf52832_xxab SoC, with a SWD interface. The board was working fine, but suddenly the debugging interface stopped working. Any idea...
I am curious whether there is a correlation in distance between different devices in a BLE connection.
A picture is attached to describe the situation.
A sensor-board...
Hello dear support team, We are in the process of designing an enclosure for our device. The enclosure is going to be molded and we would highly appreciate your support to...
My requirement is to send from Controller Device to NRF Ble Device through UART of 40Bytes at the rate of less than 1ms. Currently I am using ble_app_uart example as a reference...
Hello,
I am working on the ble_app_template example, nrf52840, SDK 17.0.2 and Segger Embedded Studio version 5.34. I have added multiple custom services to my code, however...
Hello,
as part of my project of wearable solderless modules, I've packed the nRF5340 to the same 20x20 mm form-factor - it was described earlier as part of the https://devzone...
Hi,
We have the nRF52811 in QFN48 fitted to a number of products, with the chip showing 'QAAA0 1850AA'. Does this mean that it's an early Revision 1 ? The Errata in the...
Hello,
I'm new in the Nordic sphere and I'm starting in embedded programming. I was confronted with the following problem and I will try to give as many details as possible...
Hi,
got a question about UART and maximum bytes it can receive in one burst or "packet".
Using nRF52382 and SDK16.
Recently I've been developing a new app in which UART...
