Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
I'm trying to find the UUID for the 'Time Second 32' characteristic described in the GSS v2 available here , but I can't find it in the Bluetooth Assigned Numbers document...
I browsed the Infocenter and found 'lots' of information and the instruction to install nRF Connect so I did. I hadn't decided which DK I needed to do what I wanted so when...
I continue to be confused by the Nordic setup of projects. There are a bunch of different demos, but what if you want to compile features from different ones?
Specifically...
Hi ,
I have used Calendar example running on RTC2 for my timing feature .
Below are the initializations for starting RTC2 for my clock .
#define CAL_RTC NRF_RTC2 #define...
Thanks in advanced. Both platforms are: nrf52832, sdk17.0.2. The peripheral is based on ble_app_gls and I set static passkey 123456, the central is based on ble_app_hrs_c...
HW: nRF9160 DK
SDK: nRF Connect SDK v 1.4.2
Hello, this is to report a buggy behavior I encountered when trying to implement a BLE-LTE gateway on nRF9160 DK
First...
I want to move the UART on thingy91:nRF9160.
prj_thingy91_nrf9160ns.conf added the following two line.
CONFIG_UART_ASYNC_API=y CONFIG_NRFX_UARTE0=y
The asset_tracker...
Hi All,
I want to use DFU to update the firmware from central to peripheral over BLE , both central master and peripheral are nrf52840.
Central master can find unknown...
Good Day,
we are currently working on a project for university. For this project, we are using esb to transmit a continuous audio stream (i2s format). We sample our data...
I've read similar issues but none with this configuration:-
nRF Connect SDK 1.4.2
Blinky example
Trying to enable RTT logging
nRF5340DK board
Windows 64 bit host...
Hi,
I've come across a situation where when paired to Android 9 devices, the reconnect event that follows waking the peripheral fails. Connection parameters are
The...
For ble_gap_adv_set_configure_req_enc, is the document provided?
I saw " ">infocenter.nordicsemi.com/.../group__ble__gap__app.html" , it was not found.
Hi, There is problem that the including file from "openthread\third_party\NordicSemiconductor\libraries\fds" and already added its path to file...third_party\NordicSemiconductor...
Regarding the data encoding in Advertising, the order of the data is different depending on the SDK. Is there a problem in operation?
The confirmed function is as follows...
We are using nRF52811, is there any sample code support to set/save thread power calibration table/data to available non-volatile partition.
thanks, Webber
