Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello,
I have been looking through Nordic's documentation for the nRF9160 and trying to find voltage ranges for several pins but am having no luck. Can someone please answer...
iOS is using queued writes to send data to my nRF52832 application. For some reason, on the third queued write reply (in nrf_ble_qwr.c) sd_ble_gatts_rw_authorize_reply returns...
I'd like to build a prototype using the nrf9160DK that samples audio from a microphone and plays it back. Given that the dev board has Arduino compatible headers, I'm assuming...
Hello,
we are trying to add log functionality to our application (nRF52 SDK 15.3 SD6.1.1) and we have few questions:
1. can two uart and flash backends coexists in...
I'm trying to do step-through debugging with the nRF9160 DK using Segger Embedded Studio and it's jumping all over the place. I assume this is due to optimization but perhaps...
When bluetooth only is enabled, the program has no problems. After adding USB, the program crashes。 How am I supposed to initialize it, is it a matter of order
<info> app...
Hi,
I'm currently trying to use advertising extensions with my nrf52832. However once I use the
BLE_GAP_ADV_TYPE_EXTENDED_CONNECTABLE_NONSCANNABLE_UNDIRECTED
type...
Our device uses an nRF52840 and we are using SDK v15.3.0 and soft device v140.
In order to optimize power consumption, I want to make a delay function using the RTC (with...
Hi,
We are designing a device based on nRF52840 that implements the Zigbee ZBOSS stack. We are interested to get ZB NVRAM configuration (network id, bindings, reports, etc...
After not having used my Thingy52 for a number of months, I decided to get back to tinkering with it.
When switching it on, it briefly shines a red light and nothing else...
Hello,
I am using the DWM1001 board and would like to receive some bytes over UART to the nRF52832.
I want the device to wait for a certain number of bytes from UART and...
I am using BLE UART and want to incorporate BLE bonding so that IRK keys get exchanged and can resolve the advertisement packet. I am planning to use privacy mode.
Can you...
Hi, I have followed the steps of generating a new .h file for my custom board (save as of the PCA10056.h board, modify the file, then generate a new macro in preprocessor...
Hi,
Is their any method to listen the MQTT-SN topics inside Rpi? I would like to listen the MQTT-SN messages and send it to my own cloud. Is it possible? I have tested...
