Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi,
We are developing sensors with the nRF52840. We send data packets of approx. 160 bytes with 25 Hz. We interact with a PC (Ubuntu - bluez 5.48) which works with one sensor...
We are using a Nordic 100028 usb dongle programmed as a ble uart central to interface with our ble uart peripheral based boards. The subject line pretty much says it all....
Hi,
I'm trying to flash the asset_tracker application to the nrf9160dk. I use Segger Embedded Studio for building the project for the nrf9160_pca10090ns board. However,...
Hi,
We are using a NRF52840 chip (SDK 15.3) in an application where we use the softdevice (S140) in combination with 2 UARTS: one for sending out debug output (UART0 - nrfx_uart...
Hi, We have a nrf52 which runs some project using ANT, now we would like to implement BLE for UART communication between a phone and the unit. The code base is already extensive...
Hi,
I just connected an nRF91 dk to nRF Cloud, which worked fine. However, for some reason the GPS says I am in Trondheim, while I am clearly somewhere else in the world...
I try to communicate with NRF52832 with NRF51822 for the example radio receiver and works well with SDK5 12 3
when I try to communicate with E73 (NRF52840) board(E73(2G4M08S1C...
How to push Initiator to resolve its private address (seen at direct_addr of adv_report) when bonded private Advertiser does a direct advertising?
I need the only Initiator...
I've followed the procedure on the nRF connect cloud to verify the SIM card and add the LTE device, only once the LED3 and LED4 blink at the same time like it was connected...
We are using a NRF52840 chip (SDK 15.3) in an application and are having issues with the startup of the board. I managed to create an example application where I integrate...
Hi. I have attempted to add an out endpoint to the HID usb generic example (only 1 in endpoint in example as it is a mouse).
However it is not working. When connected my...
Is there any UART examples by directly accessing the registers?
Based on SDK15.0.2, for NRF52832 or NRF52810, higher freedom, higher memory utilization.
Hi, I measure current in beacon in Long Range mode. Behind 3 current peaks witch represent TX on channel CH37 CH38 CH39 there is a strange current peak, witch I don't understand...
Hi,
I can't build any samples anymore for my nrf9160-DK using neither SES nor CLI only.
I followed the "Getting started assistant", pulled the v0.4.0 version of the SDK...
