Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi,
I'm following this tutorial . In challenge 1, I was asked to change the transmit power level of the device.
Challenge 1: Try to add and populate the "p_tx_power_level...
Hi,
I am trying to integrate some ble code into my project but it keeps giving me errors like:
Error[Li005]: no definition for "ble_advertising_on_sys_evt" [referenced...
While developing code for our custom board, we ran into a filesystem corruption issue with fatfs+qspi block device and multiple directories. We were able to reproduce the...
I have problems running the ble_app_uart_pca1004e_s112 on a custom nrf52810 target devivce. The custom nrf52810 target is a custom board with the Rigado BMD 330, which is...
Hi there,
Please see the video for a full run down: https://www.youtube.com/watch?v=nIeIUMutBlU
Basically, I have a perfect and verified design that's been in the...
I'm using python code based on the heart_rate_collector.py example in pc-ble-driver-py to scan for devices and connect to a peripheral device.
This all works fine, except...
I have an existing Firmware (build on Crossworks) that has correct "floor" power consumption (< 10 uA during sd_app_evt_wait() on my setup).
I migrate my code to rune with...
I am stuck with strange behavior of s140 softdevice version 6.1.0 and later for ble_app_template example on nrf52840 preview dk(pca10056).
As I am planning to remove LF...
Hello,
We need to produce a driver for the ST25R3911B NFC chip working with NRF52840.
We just need to read NFCA tags so we thought that the example nfc/tag_reader included...
Hi i am using SDK15.2, nrf52832 board.
Which function is necessary to achieve multilink in example code. I dont understand how the central is connecting multiple peripherals...
I just purchased this unit and followed the setup instructions. I did not perform any flashing. When I plug the usb into the computer the jlink drive doesn't show up in Windows...
Hello, I am not sure if this was noted before. I didn't find anything about it. This is more of a suggestion. I was looking to use Thread CLI Example to use with the pca10059...
Hi,
I am using a custom board with the nrf52810 and trying to interface with the SHTW2 sensor. The sensor has an I2C interface and hence I use the TWI peripheral for this...
Hello,
I have a question regarding BLE_GAP_EVT_CONN_PARAM_UPDATE (nrf52840, SDK 15.2).
I'm evaluating the BLE_UART example using multiple peripherals. The goal is to scan...
