Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
This keeps happening every time I stop the program for a while and then resume execution.
N.B. I did put a breakpoint trying to catch the problem.
Softdevice s132 6...
Hi All,
I have more boards on which I have loaded the code ble_app_uart_c (nRF5_SDK_15.2.0_9412b96) which I use as central devices and I have other boards on which I have...
I need to send the following sequence of bits through TWI
start bit | 7 bit address | write | slave ACK | stop bit
I looked through the twi_hw_master.c and it seems...
When building a project that compiles the hal_nfc_t2t.c, it errors for nRF52840, but works for nRF52832.
For the nRF52840, I get these errors:
Looking for some of the...
Hello, I want to transfer a large file (approx. 1.5MB) over BLE using nRF52 Module in a way where BLE Host and BLE Controller will be on the nRF52 SoC and the application...
I added ams service to my project, and I tested with my iphone 7P, seems all goes well. But today I tested with my iphone 5S, sometimes the hardfault exception raise.
Hi Nordic,
I'm trying to use a nrf52832 dev kit (v1.1.1) with NRF Connect (v2.5.0 on mac) to communicate to my device (NRF52832). My device has implemented MTU exchange...
Is there something on the specifications regarding the structure of a node? We have a node currently with 3 Elements:
El0: Light controller: Config model, Health model,...
Dear Sir,
I am using SDK15. Softdevice s 132, and nrf52832.
I was working with code 'ble_app_template'.
I was trying to find out the transmit power set for the...
I am trying to create a datalogger onto a uSD card with a fat file system. I have been able to run the fatfs example which creates a file on the uSD card, NORDIC.TXT. The...
Hello
We have a double problem, the CPU wake up doesn't work, but the sensor who wake up the CPU is correctly configured ant the interrupt pin go low to high when the temperature...
Hi Sir
We plan to implement our own DFU controller on host MCU to upgrade on board DFU module by UART.
Zip file will be generated by nrfutil and saved on flash.
Can...
Hi,
We've developed a BLE HID device with mouse and keyboard capabilities based on the nRF52832 and SDK 14.0.
We're interested in declaring the CoD as " Combo keyboard...
SDK : nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac
segger studio
I merged uart peripheral into simple coap clinet example
this is errors:
Output/Release/Exe/thread_simple_coap_client_pca10056...
