I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi, I want to send 9000bytes one sencond.But when I send these bytes it will return error code is 19.
I had increased the ATT MTU to 274 with the function of nrf_ble_gatt_att_mtu_periph_set...
Hi everyone,
I'm playing with the nRF52840 dongle (PCA10059) but I'm not able to program it using nRF Connect (v2.6.1).
I open the sw and connect the dongle, choose...
I am trying to see onboard SD card via usbd_msc and I can not achieve that. I am sure SD card is connected properly and working as I can mount it and write files to it form...
Hello ! Hope I can get help with this as I am completely new to this and dont get a hang of it yet. What I am looking for is to be able to use the servers as clients. I have...
I use nrf52832-AA, S132
I use Fstorage from 0x68000 to 0x73FFF in flash memory.
Reading or writing data from that memory.
It doesn't have any problem working normally...
Hello Everyone,
I am newbie to nordic BLE environment. This maybe a silly question.
Currently I am using nrf51 DK with SDK11, S130.
Data to be sent through SPI:
...
Hi,
I was trying to add generic onoff server model to the dimming server example in order to On/OFF and Dim the LED on the nRF52 Dev board using nRF Mesh App. I added all...
With 100 battery powered bluetooth long range slave nodes connected to one master. To increase battery lifetime, Is is best to connect/disconnect all slave nodes to the master...
Hello,
I have the following scenario:
The device boots and starts to advertise.
When the central (android phone or iPhone) connects, peripheral requests bonding and...
I am using sdk 11, s130, nrf 51822.
Before getting into the question I ask in the title, I would like to ask this first:
1. Is it correct that every time I call pm_peer_delete_all...
I'm trying to integrate buttonless DFU in BLE app uart example. I added the file: ble_dfu.c, ble_dfu_bonded.c, ble_dfu_unbonded.c in the project. I added the following folder...
It's battery operation so I want to know how to setup 1sec timer and goto sleep_mode(power_down) after 1sec beacon scanning.
I'm using WDT to setup 60sec WDT reset so I...
Hi,
May I know what is the hardware layout for measuring external voltage using SAADC? I may not be understanding the infocenter or the datasheet for setting the external...
In the `Serial Interface`, the `Bluetooth Mesh Packet Send` command does allow specifying the `Time To Live` (TTL) for arbitrary packets, but there is no field for `Retransmit...
