I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hi,
i try to establish a communication between 3 sensors in the following way!
Node 1 should broadcast messages to Node 2 and Node 3 as Peripheral.
To establish a...
Hello,
I am using pca10028 and sdk 12.2. I have interfaced temp sensor with nrf51 and now I want to store that data continuously in memory of nrf51. I want to store min 4k...
Hello, I want to program and debug the nrf52840 device but I'm kind of stuck at the programing range/address issue.
I'm using my customized board so I doubt Nordic Semi...
First I register the address of the central device to the peripheral device. When I work with a single peripheral device and a single central device, I can send commands from...
I'm trying to understand the subtleties in a Gazell link setup with multiple devices and a single host.
The documentation in the infocentre suggests minimum timeslot_period...
Hi,
Just wanted to confirm what the average current measured by the PPK represents. So for example if I have AVG in average window as 2.5mA, is that only the BLE (i.e....
Hi,
I found a bug in ble_app_gls example from SDK_12.3.0 / s130.
If user enters a wrong passkey, the app ends in a app_error_fault_handler exception and the central keeps...
I think I found the source of many of my recent problem. The print in Segger is going crazy.
I found out that if I increment a simple variable and print it when I hit debug...
Hi,
I am using the nRF52-DK as a device like beacon encodded with the original code of "nRF5_SDK_13.0.0_04a0bfd\examples\ble_peripheral\ble_app_beacon.
I want to change...
I am beginner of 52832. Current software is based S132 4.0.2 and SDK 13.0.0. Test platform is based on PCA10040.0
My problem is application can not start normally in merged...
Hello,
I am using nrf51 and sdk11. I have one code and I am trying ti build hex or bin file for this code. Now the code size exceeds and so I am trying to build using makefile...
I am learning about FPGA. I have question general question related to it.
Doc1.docx
A FPGA is connected to a 14-bit DAC and to an output amplifier. The DAC have a sampling...
Using S132 v4.0.2, is it possible to disable DLE (i.e. make it NOT set the LE Data Packet Length Extension used bit in the LL_FEATURE_RSP)?
Alternatively, is there a way...
experimental_ble_app_multiperipheral_pca10040_s132 connectivity issue.zip
I’m getting an LMP Response Timeout disconnect reason about 50% of the time when trying to get...
