Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Does anyone had controlled LoRa module with nRF5x??
I have nRF51822(BLE400(PCA10001)), nRF52832(PCA10040) and Semtch SX1276RF1JAS.
I hope to control LoRa module using nRF...
Hello All,
I am looking for a stand alone small transmitter/receiver that can be powered from a watch battery with a range of at least 300m. Is any of the nordic solutions...
hi,
i am working on code which require to store data array of 20x20 to store in flash area using FDS or any other possibilities.
1)i confused with FDS concept. how i can...
Hi,
we are now in the second round of prototyping - we'd like to move away from the chip-antenna based design to a PCB antenna. We have come up with two different ideas...
Here
My device (chip nrf51822_xxAA) exist softdevice 8.0.3 and BLE uart application work fine which flash by the ST-link in Keil MDK(5.20).
Now I try to add bootloader to...
Hello
I've found your example in the dev-zone and migrate the project to SDK10 and will probably do the same for SDK11.
However, I've got a problem in my project. When...
hi,
i want to implement rtxos in my nrf52832 application. one of the nrf52832's feature is ARM Cortex -M4 32-bit processor with FPU, 64 MHz.
my question is, why the...
Dear Nordic.
I am developing bootloader without SD (s120_nrf51822_1.0.1).
And after execution of bootloader, jump to application working with SD.
Flash composed like...
I tried to compile blinky sample in SDK12 with make tool-chain. I got 3 errors:
Makefile:214: Cannot find include folder: ../../../config/blinky_pca10040_s132
Makefile...
I converted a project from uVIsion to IAR, and I get an error when I use app_timer_start(); the error says: Error[Pe167]: argument of type "void ( )(void)" is incompatible...
I don't need to connect the master with the peripherals, but i have to know how is the maximun quantity of scan response that can accept the master.
In the example ble_app_multilink_central...
In trying to move to SDK 12.0.0 from 10.0.0 I get the error:
"...components/includes/app_error.h:33:23: fatal error: ant_error.h: No such file or directory
#include "ant_error...
Hi,
I want to run BLE mesh network example on my Dev board to understand it better.
I am running it on SDK v8.1 and using ble_app_proximity example S130.
Following...
Hello,
I'm using the "experimental_ble_app_blinky" on the nRF52 DK, and I would like to reduce the power consumption during the advertising.
Indeed, during the advertising...
Hi,
I am currently designin one of our product with a nRF51822 QFAC included, and I need to store 17k-bytes in a non-volatile memory.
I am writing the firmware using...
