Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I`m representing a Norwegian company that wants to etablish contact with developers that can help us develop BLE 4.0 firmware/app for ios/android. We´ve been in contact with...
So I made my own version of blinky using version 11 of the SDK with the S130 SoftDevice. This works fine and I can flash it to my dev kit (nRF51 PCA10028) with no issues....
I'm using s120 v2.1, with SDK 9, on an nRF51 with 256K ROM and 16K RAM. With s120 I only have 6K of usable RAM for my application. I am running critically low on RAM, and...
I am using a nRF51 dongle as a BLE tranciever and using UART to communicate with an 8bit AVR. I used BLE_APP_UART peripheral example and mostly just changed the pins used...
Hi,
I am trying to update the battery level of my Battery Service but get keep getting an error. The error code is : 0x00003002. I cannot find any mention of what this...
I am trying to start programming in nrf51822 module with the waveshare kit. but the kit always shows the error as switch to boot-loader mode . how to solve this problem?
i am using nrf51822 wavshare kit with ulink2 debugger.
when ever i try to program the kit using keil the error pops like "overlapping of address in 00014000H".
then...
Hi,
I am using nrf51822 and SDK 8.0.0 , SD2.1.0 as an central and SD8.0.0 as peripheral. I am following ble_app_multilink_central and ble_app_multilink_peripheral example...
Hello,
We have a custom board using nrf51822.
In keil the board is detecting at 20khz clock for SW port in the debug window, we are able to program through keil.
...
This fork of the MBED CMSIS-DAP firmware seems to be the latest updated one. The title says, 'Interface firmware providing USB CMSIS-DAP for debugging, USB MSD for programming...
Hello,
I try to change a value by using sd_ble_gatts_value_set(...). If there is a connection, this works fine. But now I have to change the value also, if there is no...
Hi again.
I'm using nRF52 DK board in Ubuntu. I can flash the device with the blinky example (I haven't yet tried the softdevice tough), but I cannot really get any traces...
20160316_113235.jpg Hi guys,
i have 20 nodes and a central in my network, that are very close to each other except central device ( All of nodes are in a approximately...
Hi,
I'm wondering why are there scan parameters on creating connection? If I refer to SD130, create connection function , there is a note which tells us that if scan is...