I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi
I am using the nRF5340 DK board using its P20 trying to flash an LED blink code to MDBT53-P1M (RAYTAC) I/O shield. The LED is connected to P0.31 of the I/O shield. By...
I am using Bluetooth for DFU in NCS version 2.6.1, but I encountered an issue in Device Manager that says, "There is no free slot to place the image." In the JLINK RTT, I...
Hi
I am new to the nRF52832 + nRF Connect and have recently purchased the nRF52 DK. Sorry if this is a simple question, but I want some clarification.
I have an external...
We have a custom board with an nRF5340 connected to a W5500 ethernet interface. The interrupt handler for the W5500 is never executed, despite the interrupt signal being asserted...
Hello, In the DevAcademy lessons I'm currently running blefund_less2_exer1 on the nRF52840 board. Successfully build and flashed firmware using Visual Studio Code enfironment...
Hello, I am trying to find out my nrf 52840 chip revision. I have tried using the NRF_FICR register but I couldn't find the revision there. I found that the variant is AAD0...
Hi
This is a project that reads sensor data and transmits it to the phone. Currently, the sensor data is read and transmitted to the app.
However, if there is 0x00 in...
anyone can tell what is the "Top right-hand side" sector?
Please see below screenshot.
Left hand side is what I dragged and dropped "merged.hex" from \asset_tracker_v2...
I am working on a module MS12SF1(nrf7002+nrf5340). I am using wifi,ble,sdcard,uart and https functionalities in my code. Currently my flash usage is 72.44%. I also want to...
Hello,
I have an aplication that connects to a LTE network and sends periodically a post request with some information to a http server. To get IP server address, I use...
Hi all,
I have an issue with putting my second boot slot on an external SPI flash. There are more people on the Q&A with issues in this realm, but none that I found were...
In our custom board, nrf5340-nrf7002 ,using external RTC ECS-RTC-SOP8-5101A RTC module, which is connected via the I2C bus.
We have configured the RTC's /INT pin (P1.01...
I am using a nrf52840 dongle. I have my own device which has BLE and I am connecting to an app in mobile phone our bluetooth. My goal is to check for the security level what...
Hi , on this code there are not any problems, ,it runs good. but the problem is current.it is 36uA. it is more than ecpectation. because in datasheet.
adxl362 current consumption...
nRF52833 Onboard jlink is broken what to do?
nRF52833 Onboard jlink is broken what to do?
Who can tell me how to make it work, and nRF52833 comes with Debug in and Debug...
