Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
I'm new to nRF9160, Nordic SDK and the build process (for Zephyr, etc.)
I'm new to eSims.
If I solder an eSim chip to the footprint on the nRF9160 DK board, how do I load...
Hi, all
My nRF52840 board is running in the extended advertising mode.
My Android phone can scan it, but my iPhone X can't scan it.
I know that iPhone...
I have installed nRF connect for desktop .In which I am trying to connect nRF 52 DK through programmer software. As soon as I connect the development kit via USB to type B...
I'm trying a project (nrf52) where I use both twi and spi to communicate with a set of sensors (each with a different protocol (twi, spi). after enablling TWI0 and SPI0 I...
Hi,
I've been trying to run the examples of the pc-ble-driver-py library, but I can't get them to run.
Every example gives me the following error: Please specifiy connectivity...
Hi team,
I am building AWS IoT client based on NRF52833 + Ethernet Controller.
I have done connecting and subscribing/publishing to AWS IoT broker successfully, and...
Hi there,
I am trying to set up a BLE communication between a central and a peripheral. For this I have succesfully used the nRF RSCS example from Nordic. But the problem...
hi dev
I'm not sure about beacon, so I'm posting questions to check.
General Ble process is like that
1) peripheral do advertise. during advertising interval, it sends...
Hello,
I was using NCS 1.7.0 and developed MQTT and SPI slave based sensor monitoring system using nRF9160 and want to switch NCS to latest build (2.2.0). A whole lot of...
Hello
Im traying to test the csense drv example , I want touch pad button only one
if I want to use this configuration
put the USE_COMP == 0 to USE_COMP == 1
now...
Hi,
We are working on creating a custom board configuration for ease of development. This is based on UBlox BMD-350-EVAL10. Which uses nRF52832.
While I created a custom...
Hi, I am trying to measure a sensor once a second. I require to use oversampling to get 14bits of resolution to meet our target. We are observing a large step in values that...
Dear all,
so far, for my external SPI NAND Flash memory chip development (Micron 256MB SLC NAND), I have been writing and reading data with my own, very basic level, flash...
I'm getting this error when I try to init the UART:
I have app_uart.c in the project, but a little investigation shows that it's not "enabled" in sdk_config.h.
When...
