Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
It appears that zigbee, matter and bluetooth/mesh Light switch samples all use light_switch as their application in NRF Connect for VSCode. Is there a way to build and support...
We use nRF9160 with our board (with Serial LTE Modem 1.9.1). We recently started using AT#XCELLPOS=2 instead of AT#XCELLPOS=1 after that we often get into trouble with the...
My environment:
nRF Connect version 2.1.0 Board: nrf52840 DK Host: MacOS 12.6
Trying to use the Zephyr sample project called SMP Server Sample. The instructions are here...
I am following the Dev Academy course for Cellular IoT Fundamentals with the Thingy:91. The Programmer software tool's "SelectDevice" tab does not detect any devices connected...
Hello,
I was wondering if there is a <complete> example someplace with Systemview running - an example for the nRF9160-DK would be nice.
I have the following in proj.conf...
We have a nRF52840 peripheral using the S140 SoftDevice on the SDK15.3.
Our peripheral is configured to advertise with the following advertising data: flags (BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE...
Hello
Sorry for the dumb question, but how do I get this timer to work?
What am I doing wrong?
I would like to measure the distance with the HC-SR04 sensor.
...
Hello!
I am having some GPS problems with the Asset tracker v2 firmware. It can find satellites, but it doesn't track them nor do I get a GPS fix before the timeout occurs...
Hello!
Our plan is to have the whole Bluetooth stack (softdevice controller, HCI, host) on the NET core and make APP core call the functions by RPC. The board is an nRF5340DK...
In my project, I need to set REGOUT0 to 4 , to achieve a VDD of 3 volts. In zephyr/boards/arm/nrf52840dongle_nrf52840/board.c there is an example showing how to do this in...
Hi,
I was about to program my nrf52840 with minor changes in the dts and after that I cannot flash any other images to the device. This is what I get when I flash the...
Hi~ I have a new NRF52833REV3 xxAA board, and I need to read its SRAM. However, when I use the JLink command to read it, I get 524288 bits 0. I have tried recover and erase...
Hello,
I am planning on using a 0201 15nH shielded inductor instead of the 0402-size listed on the schematic for the nRF52832.
Here's the link to the component: LMCI0201...
Hi Nordic,
We are now creating a BLE central device which can connect to an BLE peripheral device for some telemetry purpose.
To address privacy concern, the BLE peripheral...
