Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
A product I'm working on uses an nRF5340 (actually a Fanstel BT40 module with an nRF5340 in it) with NCS v1.7.1.
It's got an SPI slave connection (the nRF is the slave)...
good day,
is there a guide or tutorial on how to detect different press type in single button? will try to assign different tasks per button press types (single, double...
Hi Support team,
According our spec 52832 rx is about 5.4mA, but actually i measured our example, it is about 7.1mA, may i ask where is the gap? so i suspect it is because...
Hi,
I'm developing an application based on the nRF52832 development kit. It is nrf52dk_nrf52832(PCA10040). I have used nRF Connect SDK (3.0.0) for the project development...
Hello,
I am trying to interface the ble_hid_keyboard with uart using nrf52840-Dk in SDK 17.0.2. But not able to print data from uart and even not able to connect hid keyboard...
Hi,
I have an nRF9160 and working am off of the AWS_IOT sample code. When I start the device, the error messages occur 2-3 times and then the device connects successfully...
Hi,
I'm working on a custom board with a nrf9160 µC. This board is powered by a battery and a supercapacitor and my job is to assure the autonomy of the battery.
I...
I am using 9160 to develop a product for customers, which saves the date, time and other settings in NVS. Yesterday, I encountered a problem that the product could not start...
Hi Nordic team,
Is there any sample project which implements DFU controller in nRF52832 central device? I need to update peripheral device firmware from central device...
We are using SDK 17.1.0 with SoC nRF52832 and Soft Device S132.
We want to configure the soft device to enable the TX and RX GPIOs to talk to off-chip power amplifier. Looks...
Hello there. I would like to know how can I read the counter value right before resetting WDT directly from the register.
That means right before calling:
I want to know...
Hello,
I'm developing a NB-IOT application on the nRF9160-DK based on the 2.6.1-rc1 SDK. I'm experiencing a bug where the firmware gets stuck while serving a send() request...
I am successfully able to use pc-ble-driver on nRF52840 Preview DK using latest connectivity firmware loaded by nRF Connect.
I want to use the same functionality on FENSTEL...
I am using the nRF52840 (with SDKv17.0.2 + s140_7.2.0) and made a custom FW based on the ble_app_hrs example. My custom HW has a 128MB MX66U1G45G flash memory chip.
The...
Hello,
I wanted to build a temperature and humidity sensor application for my custom board using NRF5340 SPI master board. The sensor we are using here is "SHTC3" please...
