Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
In the beginnig of this year I used to test my edge Impulse Zephyr project with nRF connect Segger Embedded studio and it's worked, but now days I having a problem with Segger...
On Zephyr 2.7 I used following snipped to connect a GPIO pin (ADC_nDRDY) to a SPI TASK (simplified):
On Zephyr 3.0.0 we experienced immediate crashes.
I then saw that...
The RPM package for Linux x86 64 bit has its architecture set to amd64, but the correct value should be x86_64. This problem prevents installing the RPM on current versions...
Hi,
IC nRF52833
sdk:nRF5_SDK_17.1.0
1. Does BLE have the concept of signaling test mode and non-signaling test mode?
2. Is DTM in signaling mode or non-signaling mode...
If we are using the 5340 in high voltage mode (VDDH); what IO voltages are used for the debugger interface? Looks like our HW designer has taken the lip voltage 4v3 to 3v5...
Hello,
We are using Nordic sdk 17.1.0, with segger studio of 5.70a.
Here we are trying to merge ble_app_uart example with ble_app_beacon example.
Actually ble_app_uart...
Hello,
I've been playing around with the PPK2. However, when I power a 1KR resistor with 3V I get an incorrect measurement.
The Expected current is 3/1000=3mA, I also...
When I build the smp_svr example, which I think contains firmware update over BLE functionality, the flash memory is reported as about 72% full.
Does this mean when I...
Hi, I use AT command controls the GNSS use Serial LTE modem example in my 91DK board.
I send command as below example,
but my uart tool receive as blow, and i don't...
What is the difference between nRF 5 SDK (downloaded in .zip format) and nRF Connect SDK v1.9.1 ?
I am using VSCode through nRF Connect SDK v1.9.1 and I find it easy to...
I am connecting a nrf52480 board (Adafruit Feather nRF52840 Express) as Connectivity chip and a custom board as Application chip for Nordic serialisation. Able to establish...
I am connecting a nrf 52480 board(Adafruit fether express) to a custom M4 cortex board with the help of nordic serialisation library. I have ported the serialisation library...
Hello all!
I'm using nRF52-DK to develop program which is controlled by smartphone (BLE) and do ADC&GPIO in the circuit.
GPIO acts like this: High-Low-High-Low.... it...
Hi Nordic,
I am working with nRF52840, sdk17.1.0 and do the following test:
I use nrf_gpio_cfg_output(), nrf_gpio_pin_set(); to set gpio P1.00 to high and use nrf_gpio_pin_input_get...
