Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
Hi,
We are developing a custom hardware that has MDBT42 module with nRF52832 chip on it. Our project is based on the ble-throughput example and this module is using the...
Hi Support,
i did some changes(add some folder ) in gps sample program for nRF9160DK(v1.1.0) and using nRF SDK connect , toolchain 1.7.1, and getting error ( error: Aborting...
Hello
I am working on to flash my firmware binary into external flash by using nrfjprog commandline tools.
I have used below command to program and verify the external...
HI,
I am using BL653dvk board(customized ). I am following this link ( https://devzone.nordicsemi.com/f/nordic-q-a/82430/ncs-external-flash-ota-change-qspi-to-spi ) and...
Hi All,
I usually use nrf Connect for desktop in conjunction with the nrf52 Dongle (nrf52840 chip) to perform DFU's on my devices during development. but recently I have...
To get this example working, both major cellular providers here in NZ, Vodafone and Spark (M2MOne) require a specific (different) APN in order to access their networks.
...
Hi, I want to connect my PC to nRF-52840 through BLE. I git nRF connect for desktop and downloaded the BLE software to another PCA10056 and i managed to connect but i can...
Good morning,
We have a new equipment based on the nRF52840 and s140.
Just now, a new problem has appeared and it is very strange, as it seems to be a ‘random’ error:...
Hello,
I am currently using Fanstel dongle, where I am trying to trigger the USB DFU with nrf connect programmer (buttonless). The example which is provided works on the...
Hello,
I am using an nrf5340dk and I am trying to create a qdec sample using as reference the wheel module.
I have added set the CONFIG_SENSOR and CONFIG_QDEC_NRFX to...
Hello Nordic Experts,
Recently, I have been investigating the radio timing for advertising, I tried to find answers online, but I failed. To explain more clearly, let...
nrfutil is required to program the nrf52840 dongles being distributed at the 2022 Zephyr Developer Summit. west is the tool used by zephyr to install, build, flash, etc. ...
Hi,
I have a QSPI flash device with a weird bug (I think). Basically, when the RDSR command is executed, the HOLD pin needs to be held high otherwise the flash chip status...
Hi,
I'm developing with Segger and nRF52832.
I'm writing a code that makes two tasks into RTOS and sends data to BLE after I2C communication and SPI communication respectively...
Hi, I am using NRF5340 and I want to connect it with a 128x64 oled display with the I2C protocol (Scl, Sda, Vcc, Gnd), I have been trying to connect it for more than a week...
