Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi Nordic team
I tried ncs 1.9.0 peripheral_uart sample (\TOOLCHAIN\v1.9.0\nrf\samples\bluetooth\peripheral_uart) at PCA10095 v1.0.0 DK.
1. Application core: Board is...
Hi, I'm trying to get started with unit testing in Zephyr by running the sample in samples/subsys/testsuite/integration. I'm using ncs 1.7.1.
I copied the sample to my workspace...
System details:
Board: Custom
Chip: nRF52832
PCA Number: PCA10040
SoftDevice: S132
SDK: Version 16.0.0
Until recently, I have had no issues using the TWI module...
I use nRF52840 in aQFN73 package. Can I assign QSPI contacts to G1, J1, L1, N1, R1, U1 pins? Or should I strictly follow the recommendations from the datasheet? Thanks.
Hi All,
I have an application that wants to send 1 array every 2ms. There are 10Bytes of data in the array.
I will be based on 1Mbps, MTU size = 23byte, Payload = 27byte...
Dear Sirs,
I use the standard printf() function to communicate via UART (with retargeting).
Unfortunately could not find a way to not overwrite a buffer.
The only workaround...
I have configured EasyDMA RX.MAXCNT=256 and set EVENTS_ENDRX. If >=256 bytes arrive, an interrupt occurs immediately. And if only 128 or 10 or 203 come.. byte, then I'll never...
Hi,
I'm using nRF Connect SDK 1.7.1.
Is it possible to mix polling & interrupt driven UART API?
I have a situation in which I want to receive input once in a while...
Hello,
I am using the Bluetooth Low Energy application to interact with my device under development. I notice that if I set the Write No Response property on an attribute...
Hello, I have recently started an evaluation on nRF9160 DK in the UK. I tried to run the Serial LTE or AT Client examples but I was not lucky to register to a network. Using...
Hi to everybody, i'd like to know if there is a way to enable/disable mesh message relying on a node locally by the firmware without using a configuration client or a provisioner...
Hi Nordic, Since the last update of the Programmer application of the NRF CONNECT for Desktop, I've been seeing this error: I've NRF52833DK // PCA10100, and up there it says...
Hi Sir/Miss,
I use programmer v2.3.1, J-link and nRF52810.
After I connect to J-Link which displays nRF52840 in UI. In log windows, it's normal.
Please check below...
