Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Hi,
is it any possibilities to multilink central with s112 in nrf52810 chip?
using sdk: sdk14
actually, i am using sdk14 with one central and one peripheral is fine...
Hello, All,
When using UART on nRF Connect SDK to communicate between nrf9160DK and nRF2833DK, I found that the data length of a packet sent by the UART on both sides is...
Hi,
I have started a new project that will use I2C and SPI devices. As a starter I took the example at /examples/peripheral/gfx/pca10040 since I am using a ST7735 based...
Hello sir,
I am using nrf52832 as Dev kit board with using Button 1 for long press event for an interval of 5 sec .I have defined the BT0_LONG_PUSH as BSP_EVENT_KEY_0 which...
Hi,
I'm trying to build the Zephyr NVS sample in SDK 1.6.0 and SDK 1.7.0 for nrf9160dk_nrf9160ns (Non-Secure) and build operation is failing with errors.
../src/main...
NCS V1.7.0
VSC IDE
In VSC you can create a custom board.
when i do this for the nRF5340 and build, it does not include the network core.
it also does not appear...
Hello
in order to reach low power mode I use the following :
bsd_shutdown(); // 3.4 ma.
nrf_regulators_system_off(NRF_REGULATORS_NS);
how can I recover from...
Hey,
I have a custom board that is pretty much the same as an evaluation board I got. I use the secure_bootloader_uart_mbr_pca10056 to enter and execute a DFU.
On the...
Hello,
I tried to check SPI communication with a test board.
However, I couldn't read the device info from the max30003wing board.
Board: NRF52840DK --> MAX30003WING...
Hi
I've been having issues with this since the first time I installed VS Code and ncs for VS Code. I've used the Nordic's official YT setup guide while installing.
The...
I am not able to flash nrf5340 using seggar embedded stdio and nrf connect .... nothing seems to be working!
I am attaching the log file
nrfjprog version : 10.13.0
JlinkARM...
I am new to NRF chips and trying to read, write, and erase to flash using nrf_fstorage. I have looked at the example project flash_fstorage and I am able to successfully read...
Hi All,
I'm trying to generate an interrupt on the X PWM's falling edge. My idea was to setup the PWM and count the number of falling edges using PPI & a timer / counter...
