We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I have a custom board, with nrf5340, nrf7002 on it.
I would like to get the uA levels of power consumption I see other nrf5340 projects talk about (eg here ) when my application...
Is there any characterization for the nPM1304 (or any in the series) with a charging input voltage in the 3.5-4.0 range? I have a ~4V power source, but depending on load it...
Hi,
I'm developing a project that requires to write GPS data to an SD card. I'm using Nordic SD card library.
I'm able to initialize and interact with the SD card only...
Hi there,
I am trying to send large data files via BLE notifications. My setup is nRF5340 development kit sending data to connecting devices (phone, PC).
I have gone through...
System description
I have an nrF54L15 mounted with an external 4 Mbit External flash with FATFS configured
Filesytem config:
# FatFS File system
CONFIG_FILE_SYSTEM...
Hi
About nPM1300
We will use load switch to drive haptic function and its peak current may up to 0.4A~0.5A@25us duration,
I see the spec show the load switch with maximum...
Hi,
I'm running an app on nRF52840 (NCS3.02) based on the BT shell example.
I did the following modifications:
- shell runs on USB-CDC instead of UART
- using NRFX...
While checking the Channel Sounding samples, I came across the concept of Channel Sounding Security Levels . I have a few questions regarding how this is handled in Nordic...
Hi,
I was wondering whether the nrf54H20 can utilise the BLE sniffing firmware used with the nrf52840?
If not, will this firmware be made available in the future and if...
I have a project that was built with SDK and toolchains 1.7.1. This firmware is used in a fielded product. I can't upgrade it to a newer version of the SDK without having...
I am currently using the nRF54L15 DK board along with an external host to develop Channel Sounding functionality. After reviewing related support tickets, I understand that...
I tried updating my project from NCS 3.0.2 to 3.1.0, but it hardfaults at boot. Doesn't log anything to RTT. The warnings/errors at boot in the screenshot can be ignored,...
Hi everyone,
I’m working with the nRF54L05 MCU (SDK v2.9.0) for my application.
From the documentation, I read that in the system_off demo, when using the z_nrf_grtc_wakeup_prepare...
Hello,
I am working on nRF9160 custom board. Since I am reprogramming a lot, this issue is kind of getting on my nerves. Here is the issue:
Usually modem takes couple...
Hello! I purchased some nRF54L15-DK 0_9_3 boards. Recently, I have been conducting relevant tests on the nRF54L15-DK 0_9_3. I want to test the low power consumption performance...
