Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi,
I'm trying to catch my NRF packets with nRF Sniffer for Bluetooth and I can't find them (after starting advertising).
On the other hand - I'm able to connect to the...
Hello,
I am stuck on the step of getting the Thingy91 to start working.
I am following this tutorial: https://www.nordicsemi.com/Products/Development-hardware/Nordic-Thingy...
Hi,
i am working on nrf52dk. i have already implemented dfu with button. i want to implement buttonless dfu. as there is a example provided in ble_peripheral with name ...
I'm more of a programmer than an electronics person so I apologise in advance if I misuse terminology or if the answer to this would be obvious if I had more experience. ...
Hello.
I want to raise the SDK version, what should I do at that time? (Example: v16.0.0 → v17.0.2) Should I overwrite all the old SDK sources I'm using with the new SDK...
Hi, I'm using the PWR_MGMT SDK 17.0.2 demo code on my nRF52 DK.
Q1) After enabling parameters in the sdk_config.h, the nRF52 DK could enter the Power Off Mode if I press...
I am trying to conduct a device firmware update using nrfutil's dfu ble functionality. Here is the command:
However, running the above command results in the following...
Has anyone used SDCard interface with either 52840 or 5340 in anything other than SPI mode? I just noticed in the SDK 15.3 code we are using SDCard is in SPI mode. Seems max...
Hello,
I want to connect an external led to the nrf5340 pdk to perform the same function as the blinky example.
I connected this led to D0 (PIN P1.00), but I don't know...
Hi,
We are trying to send a mesh packets containing 72 bytes from client to server with reliable message transmission method (Using access_model_reliable_cancel() based...
nRF52840 with SoftDevice s140, rev 7.01. For this errata, the work around is to use READY instead. Is the SoftDevice doing this? I can't find any info. I did find a related...
We're using the nRF52840 along with SoftDevice s140 version 7.01 for a medical device. Reviewing the nRF52840 Errata sheet, Rev2, there is an errata "242 NVMC: NVMC operations...
Hi nordic community,
I'm using Open Thread Border Router build using Linux and an nrf52840 dk board, I want to show my sensor data in open thread border router web GUI,...
