Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Experienced developer new to embedded C programming here, so please forgive me if I'm missing something obvious. I already went through the GPIOTE example from the nRF52 SDK...
Hello,
I'm not sure if this is possible, but I would like to filter log level depending on which backend is receiving them. For example I would like to set the RTT to...
Excuse me:
When our tests the RX selectivity of nrf52832, the test results are inconsistent with those in the datasheet(nRF52832 Product Specification v1.4 P232). How did...
Hi,
I am using nRF5340 development board with J-Link connected to "TRACE" pins: SWDIO and SWDCLK.
In app project I have these settings in prj.conf file:
CONFIG_USE_SEGGER_RTT...
Hi Support team,
in the following link, there is a fix decribed to get lowest power down current of the UART0 of the nRF52840:
https://devzone.nordicsemi.com/f/nordic...
Hi all,
I am using the Adafruit Feather nRF52840 as my central device. My peripheral is a nRF52832 with a 9DoF IMU. (SDK17.02)
I need to stream 26 Bytes of IMU data at...
Hello,
we started using zephyr OS for our firmware projects. To implement a propriety protocol on top of IEEE802.15.4 I use the radio with CONFIG_IEEE802154_RAW_MODE =y...
Hello
I am using sdk v17. I am merging the example of ble_app_uart and crypto_aes_ctr.
I added files about crypto and set the file path. However, the path error is printed...
Hello~
I am experiencing hardfault occasionally. (once a day ~ once in 3 days)
I am testing 14 boards to catch hardfault.
The following is my setup
- hardware...
Hello, I was trying to run the sample Alexa Gadget Application on my NR52840-DK, using nrf Connect SDK v1.5.0. However, upon trying to run the application I am getting the...
Hi support team,
I am developing a product. The product needs read adc and restart advertising when no connection.
I get hardfault randomly when called the ble_advertising_start...
Hi all, the application i'm using nRF52810 for requires that I keep the device powered on all the time. However, in the case of errors (tolerable within my application) I...
I successfully compiled the micro_ecc library, but when I try to compile the project with it, I get an error. Has anyone encountered this? What can be wrong?
Build target...
We use the nRF5340 D version IC for one project, but the PCBA (main chip is nRF5340) not working, we can burn the hello_world.hex by Jlink 7.23 version, But the Crystal 32...
