In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
Dear Concern,
I am getting MCUboot build errors as shown in the below.
C:\Nordic\v1.5.0>west build -b nrf5340dk_nrf5340_cpuapp -d build_mcuboot bootloader/mcuboot...
Hi,
I have nrF52840 DK rev 2.0.1
switch to VDD, Default, SB40 is cut (confirmed by multimeter)
I have the PPK rev 1.1.1
switch DUT to DK
switch Power to DK
I...
Hi,
is possible use for DFU process as DFU server other device as development kit?
I will use it in street lighting but it not usable with development kit. I would use...
I have a couple of examples that work ok on 9160-dk and use SPI3.
However, if I try to use these on SPI1 or SPI2 I get a device not found error.
I am building with west...
hi,
i am working on timer example in peripheral folder. i am including this example in ble_uart example in ble_peripheral folder. i am getting error " 'NRFX_TIMER0_INST_IDX...
I am using the SHT21 sensor for measuring temperature and humidity, trying to connect it to nRF52840 DK Board using TWI mode.
I am unable to even scan and get the response...
I deleted the flash completely for the bootloader example, then I installed soft device. The softdevice area for nrf52832 is written as 148 kb in the documents. In nrfgo studio...
hi,
i am using working on example "pin_change_int" in peripheral folder.in this example interrupt occurs when there is state change on interrupt pin. how to enable interrupt...
Hi,
Is it possible to upgrade a S112 v6.1.1 softdevice to the S113 v7.2.0 softdevice using BLE DFU?
I am getting the following error right after the SD + BL has been...
Hi folks,
I am playing around with the A-GPS sample.
I am trying to send the fix every five seconds to the cloud. This should be possible according to the webinar last...
At my system (production) there are 6 serial ports and 2 programmer (ARM-Flasher from Segger) connected.
The nRF Connect - Programmer only display 5 COM-Ports and NO Segger...
Hello,
I am starting a new project and we are using the following:
-NRF52840
-SDK v16.0.0
-pca10056 (NRF52849 DK)
After downloading the SDK, I was able to build...
Hi,
I am developing on nRF52840 using SDK version 15.0.3 and Softdevice version 6.11
I have observed that the once you initialize the app_uart using 'app_uart_init(...
