Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I would like space in flash that can be written to during production and then never changes or is overwritten. I have explored adding a section in the linker.
Are these...
Hi there...
I am using :
Device :Custom board using nrf52840 (fanstel module BT840)
SDK : nRF5_SDK_17.0.2
SoftDevice : S140 7.2.0
In order to add DFU capability...
Hello,
Any updates on the modem firmware v1.1.3 and v1.3.0 certification status for Verizon? I was told v1.1.3 was supposed to be around Q4 and v1.3.0 was supposed to...
The actual title is too long, the problem is this.
The documentation for s110 says:
Commands to write a buffer to flash
If the SoftDevice is enabled: This call initiates...
Hi All,
I am developing a Zigbee based light controlling product using nrf52840 and nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71 SDK.
All functionality and features developed...
Hi,
I run the radio test with our PCBA with SDK17.0.2, but when I want to send "start_tx_modulated_carrier 100", there's no callback response "<info> app: The modulated...
Hi.
I am looking to implement a nRF52840 chip in my 5v battery operated door lock.
Sorry if this is asked before or should be clear from documentation, but I am not...
Hi,
Do you have an example of how to implement a serial console with nrf connect 1.4.99-dev1 with nrf5340_REV1, I tried compiling usb_uart_bridge but got following error...
There are two central sd_* methods for writing to flash - write and erase. The problem is I need to know where I can put my data without trashing something else that is already...
I have two projects exhibiting the same problem.
I have custom board using the nRF52832 and another using the nRF52840. In both cases I am using nRF5 SDK latest version...
Hello,
I would like to have confirmation that the NRF52 will be compatible with my need.
The NRF52 must be able to be connected to a smartphone, while receiving advertising...
I have problems with my custom board.
I developed the firmware with the nrf52832-dk custom and there the firmware runs standalone (with RTT logs on and without) . but now...
I use a nRF52840 Dongle as the Sniffer HW. I use 2 other nRF52840 boards, one is a peripheral (NUS) and the other is a central/peripheral (NUS). The cen/per connects as a...
Hi I have a custom nRF52840 board, and I have a current BLE UART setup. I also want to communicate with a IMU module via serial connection. Can you point me in the direction...
