I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
hello,
i added scan_rsp_data to add a name on my beacon, but now i cant see manufacturer data on the ble_gap_evt_adv_report_t structure but i can see that perfectly on my...
I'm seeing the modulated output of %XRFTEST offset by approx. 1.675 MHz from the set frequency. Modem version is v1.2.2
Here's my command:
AT%XRFTEST=1,1,1,19500,23...
Hi!
Looking at the schematics for the nRF52833 reference circuitry I see that when USB is used, the VBUS is connected to the C18 capacitor, then GND, and if USB isn't...
I have programmed my device with ble_app_rscs available on nRF5_SDK_15.3.0_59ac345. I was expecting it the main loop
the device will only consume 2 uA however it is consuming...
After a few configuration issues we have finally got a connection with the asset tracker application. However we are not getting far enough to send data.
The log shows a...
Hello,
i am trying the nrfsniffer 3.0, but all the packets seems to being dropped.
I am using:
* BLE400 with nrf51822 module (firmware flashed with stlink )
* Linux...
I am trying to make couple templates for S113 with nRF52832 and nRF52840 with and without FreeRTOS and because there is no such in the examples, I’m not sure I made it right...
Hello,
I'm using SDK for Thread and Zigbee v4.1 and I developed a network using mqtt-sn library. Since the developed application requires data publishing at a high rate...
I want to get logs via RTT (JTAG) in the connectivity firmware example of SDKV15.
I have built the connectivity firmware project using cmake and opened the project in SES...
Hello
I'm trying to implement the click and double click and long click of a button in sdk v17.
Click and long click work fine. But double-click doesn't work.
Code...
Hi,
We are currently porting our code to the newest nRf5340 chip.
Everything goes fine when the target is secure (not ending with "ns" and not defining "CONFIG_TRUSTED_EXECUTION_NONSECURE...
Hi,
I am working on a device that has nrf52 as an additional BLE chip that does not run the main logic but provides UART over BLE to the application processor (NUS). In...
Hi,
I am working on the our customized board nRF52832 , interfaced with MAX30205 temperature sensor . I am advertising the data only when it reaches the below temperature...
Hello,
We are planning to use the accelerometer in the Thingy91, we have some inconsistent results when configuring/reconfiguring, we have 2 questions:
- When we, for...
