Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
We are developing a project that runs BLE, the Nordic Uart Service, the Nordic Distance Measurement toolikt and Async UART (NCS v2.9.0). The Peripheral device shall advertise...
Hallo,
we are using the nrf5340 and the ncs Version 2.6.1.
I activated the software downgrade protection as described here Downgrade protection (nordicsemi.com) .
Then...
I just received a new 54L15DK and was attempting to port a simple 5340 project to it. The first time I attempted to flash it, it _looked_ like it was successful:
[1 0/10...
The subject issue is documented here as " NCSDK-20567: Partitioning limitation with MCUboot swap move": This issue has been open for while. These two DevZone tickets refer...
In our application we using nrd5340-nrf7002, application flow is wakeup->wifi connect->NTP time get->TCP server connect->wifi shutdown->idle->wakeup..... We are encountering...
Hi Nordic
I am curious how to test nRF54L15 BLE sensitivity and Blocking.
I am currently using:
1) nRF Connect For Desktop" v5.1.0
2) Direct Test Mode v2.4.0
...
Hi y'all.
I've been developing in Zephyr NRF52840. My code is based in Central_HR_Coded (SDK 2.6.1, Toolchain 2.7.0). I had some issues with the bt_conn_disconnect function...
Hi, I'm new to this product and currently working on the Nordic Thingy:91X and have encountered some issues that I need help with. below is the details from the serial
monitor...
Hi,
I am developing an application with LTE-M connectivity to nRF Cloud. Our previous SIM apparently supported auto-APN provisioning, we did not have to set the APN, the...
Hello,
I bought brand new Thingy53, but Thingy53 turn off during deployment and can not connect to BLE, becuase it turns off. Please assist me if possible.
Hi,
I test my nrf54l15 module(disconnect every gpio with outside),the sleep current was 3uA,seens can't not achieve 0.6uA as the datasheet said.
The nrf54L15's markcode...
I am experimenting with sampling IQ at the payload in AoD mode. Are there any differences in the configuration of the receiver in AoA mode as seen in the direction finding...
Dear DevZone,
I believe I am quite familiar to this forum due to my ongoing Wi-Fi issues with SDK 2.6.1 To determine if a newer SDK version will resolve these problems,...
Hi,
I still try to configure Nordic-Zepyr build for a nrf5340, with a BLE stack and MCUBoot as the bootloader. The application will receive image updates over MQTT and store...
