Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
I am trying to port the 'radio test' example code in SDK15.3.0 from the nRF52832 to the nRF52810 so we can do some pre-certification testing of the radio in our custom design...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
To understand TWI better, I loaded 'twi_sensor' example as is on nRF52832...
Upon initial connection with iOS device, returned connection values at BLE_GAP_EVT_CONN_PARAM_UPDATE are:
ble_event: got BLE_GAP_EVT_CONNECTED. role: 1, conn_handle: 1,...
Hello,
I using the Segger with the last SDK. I modified the ble_app_uart example, I added the softdevice to the addition files. When I run the debugger everything seems...
Hey guys, Recently i decided to get the ICM-20948 DK and exploring it. I read all the info on their site and all their guides but the only briefly get over the topic, so i...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I was going to “Batter Service”. Battery level...
Hello, I am using the PCA10056 to program a nrf52811 chip on a custom board with SDK 15.3.0. I'm using the example ble_app_blinky_pca10056_s140 I am following the steps in...
I am working on transferring BMI160 sample given in zephyr samples (\ncs\zephyr\samples\sensor\bmi160) to nrf sample (\ncs\nrf\samples\nrf9160\bmi160).
Below is the changed...
I'm having a problem with the nRF52 SAADC. It's configured for
One shot operation on Channel 0 using pin Ain4.
Gain of 1/6
Tacq set to 40us
8 bit resolution...
HI,
I want to configure HT1632 LED driver using SPI communication protocol
for that i should send commands LSB to MSB
immediately data should go MSB to LSB
My question...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’ and “nRF Connect” app.
I am trying to understand...
Hi all
SDK 11.0.0 S132 version 2.0.1 nrf52832
I want to turn on the PWM and turn off the PWM after 1 minute. The device will do BLE advertising When the device wakeup...
Hi,
I have read a lot of posts about using the internal LDO/DCDC converters or using an external switch mode regulator, but haven't seen any answers I could use.
I have...
I am looking for guidance on how to fragment data in Extended advertisement on the nRF52840. I am using the "ble_app_rscs" example to advertise in non-scannable non-connectable...
Hi ,
I need to update the NRF52832 with another different module.
I can update without problem by using the nrf connect app.
I would like to use another device without...
