I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
I've been struggling with this for quite a while now. I've got a PCA10040 to spare that I am trying to use with nrf sniffer in Wireshark. I'm using a new iMac with the latest...
I have a problem I'm using nrf52840 DK. The task i want perform is start from idle state, wait for a button signal and the go out from idle, start with a loop where the code...
Hello ?
I was surprised that the program was organically well organized.
Based on the given installation manual, I completed the installation and corrected the program...
Hi!
We are using NRF52832 and NRF52840 with custom rf protocol.
I didn't found any information about time for applying new TXPOWER value of radio module.
Can I start...
Based on mesh sdk 3.1, open NRF_LOG_ENABLED in the light_switch_server example, ie NRF_LOG_ENABLED 1, the following error occurred during compilation: Linking light_switch_server_nrf52840_xxAA_s140_6...
I had two nRF52832 where one broadcasts with encrypted data of advertising beacon info and another nRF52832 should only scan without connecting and should decrypt the data...
Hello,
We are using nRF52832xx_aa controller for our product, the sleep current consumption is approx 2 uA @25 degree Celsius which is fine with me. But when the temperature...
We are writing SPI drivers for RF chip and blocked on the below issue. The issue we are facing is the Chip Select line is not active(active low) until the TX transaction is...
SDK: 12.3.0
SOFTDEVICE: s130_nrf51_2.0.1_softdevice
CHIP: nrf51822 AC 256K flash 32K ram
GCC flags:
# C flags common to all targets
CFLAGS += -DBOARD_CUSTOM
CFLAGS...
Hi,
I want to write or change the code in to nRF52832
I have some code this code i should write for nRF52832
kindly give any suggestion
here is the my code
uint8_t...
Hi everyone ,
I have a custom PCB using nrf52840 and i measured the current consumption using PPK(power profiler kit) . The sleep current value that it show is 4.5mA.
...
Hello,
I want that two devices can connect with each other and only each other . To do this i wanted to use whitelist on peripheral side but i found that i could use filtering...
Hello.
I'm using nRF SDK 15.2 together with the Nordic 802.15.4 driver ( here ).
When trying to add the libuarte module to my project I started having mysterious issues...
