Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello All,
I have 2 evaluation boards nrf53840 EVB "PCA10056".
I would like to run on them the "ble_app_uart" in "nRF5_SDK_15.3.0_59ac345" as following:
A custom board...
let say i have a temperature sensor connected to one nrf 52840 dongle of a mesh network. Now can i make the Led of all the dongles glow if the temperature increases the given...
I downloaded the latest nRF5_SDK_15.3.0_59ac345 and some other old versions of SDK documents. (I am trying to use pca10040 development kit to program Fanstel EV-BT840F, aka...
Hi
One of our customers have complained, that our sensors are making occasional errors.
I have looked at it, and they are correct. About 1 in 8 Million packets send...
Hi, I have my custom board for the nrf9160 ,
I was able to program it through the built in programmer of the nrf9160 dk but I have an issue, when I connect the VDD to the...
I'm using adafruit_tag_reader example to read ISO14443 tag. When I put a tag near scanning area of PN532. It reads tag multiple times till I remove that tag from there.
...
Hi!
I am using IAR compiler for my project
I declare global variable
__no_init u32 uPowernResetSignature;
in my code I assign value to this variable
uPowernResetSignature...
Thank you for taking time to look at my problem!
I have managed to combine the TDK/Invensense library for their IMU MPU9250 within the SDK 15 utilizing simple TWI calls...
Hi,
I have nRF9160-DK kit and its environment is set such as nRF Connect SDK and Segger Embedded Studio.
I want to build a simple application from scratch for example...
Hi, I am trying to modify UICR PSELRESET but its not changing. Any help?
NRF_UICR->PSELRESET[0] = 0xFFFFFFFF ; NRF_UICR->PSELRESET[1] = 0xFFFFFFFF ;
Thanks
Hi,
I'm developing an application using the timeslot API for a custom radio protocol. The application also uses a number of the nRF52832 peripherals, as well as the app_scheduler...
Hello,
I'm having an issue with scripting AT comands directly into the code of the nRF9160. I'm a novice at all this so I apologise if the mistake is an obvious one.
Inside...
I get "ERROR: There is no debugger connected to the PC with the given serial number." when I run e.g. nrfjprog --eraseall on command line.
Programming/debugging using VisualGDB...
Hi,
The User Guide v1.3 in Chapter 2 (minimum requirements) states "SEGGER J-Link Software" under "Software requirements". Is there J-Link software specifically for use...
I've been developing firmware for the nrf52840 for a few months using armgcc+openocd+arm-none-eabi-gcc working successfully. I recently upgraded my ubuntu version (18.04)...
