I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
I have an nRF52810 on a custom board and can't get it to wake from System Off mode. The code:
trying it with a different way to turn the system off also didn't work: ...
Dear Nordic Support,
Processor: nRF52840 / S140 soft device / SDK 15.3.0
I have a question about the use of the HFCLK in relation to the soft device. Our board has both...
Take a look at a following code
void fmc_serial_rx_cb(const uint8_t* p_data, uint32_t length)
{ __LOG(LOG_SRC_APP, LOG_LEVEL_INFO,"\n-------------SERIAL RECIEVED : %s...
I am new to softdevices so please bear with me for long list of questions.
I am evaluating SDK15.2.0 examples one-by-one. I came across eddystone example (ble_app_eddystone...
Hi!
In older SDK (15.0) has been present NRF_ESB_BUGFIX_TIMER and it initialization. Now (SDK 15.2/15.3) defines this macro but not use it. Is it bug or obsolete code?
Hello Nordic Team,
I followed the tutorial as you say( https://devzone.nordicsemi.com/tutorials/b/getting-started/posts/nrf52840-dongle-programming-tutorial ). But when...
dear all,
I'm a newbie on blue tooth low energy development, I have some really basic questions that I hope someone could answer, thank you very much in advance!
what...
Hello,
trying to bring up the new nRF91 dk with default firmware.
Registered the eSIM. Switch sequence followed when LED 3 and 4 starts blinking, but get the devices list...
Hi I have central device which has array of MAC address to connect.
when i see the structure of sd_ble_gap_connect() i cannot pass a uint8_t addr[5] as input.
so i tried...
SDK v11.0 & NRF51822 QFAC
I encountered a problem. In the process of pstorage processing flash data, a serial port interrupt came in, resulting in a system reset.
I used...
Hi,
I have discovered a (rare) problem where the S132 stack get stuck in connected state when it is not actually connected anymore.
This behavior was first reported by...
Hi,
SDK - nRF5_SDK_15.2.0_9412b96
HW - nRF52840 connectivity chip, other controller for application chip
We are tried to port serialization application on other than...
HW - nRF52840
SDK - nRF5_SDK_15.2.0_9412b96
We are running connectivity example in nRF52840 and connected UART with serialization application over UART which is different...
First proof-of-concept super-simple nRF51 board. When we load software onto this board, will we have to tailor or configure the software to bypass or disable any functionality...
