I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
I have been using SMD modules with NRF24L01+ fitted.
The first batch I used worked fine for months.
Then I purchased another batch and found the tx_ds_active or max_rt_active...
Hi,
1. I went through the document. I'm trying the example applications Light-Switch on PCA10040 DK and NRF5 SDK for Mesh V2.2.0. So it is like the Client will be provisioned...
Good afternoon,
Following up my previous case, to which I got no reply, how can I use a queued write characteristic to write less than 20 bytes of data?
I'm using it...
I'm trying out Zephyr on the nRF52 DK, specifically I want to test the ADC drivers. Since things are moving quite fast in the Zephyr development world, there may be some information...
Hello, I'm working on Mesh SDK 2.1.1 and I'm trying to send a Relay Set message through Configuration Client. I have changed the code of models_init_cb() function inside the...
The nrfx_spim driver has an issue when chip select pin of the driver is not used.
When nrfx_spim_init is called with a nrfx_spim_config_t whose ss_pin is set to NRFX_SPIM_PIN_NOT_USED...
Dear Nordic
I have custom board(nRF52840) its not detecting through Jlink (from nRF52 DK).
I tried to connect nRF52840 dongle(using J2 in dongle) with same setup its detected...
Hi,
I am latest SDK 15.0, and using FDS library to store custom data. I have followed FDS examples but couldn't succeed in writing data to flash. When i tried to debug,...
Hi Guys,
We started to develop a mesh network with nRF52840 DK's and dongles. I have made some adjustments in the code with segger to use the server example of the led switch...
I just want to globally set the power level, and forget about it.
I have seen this post, and it still seems unclear how to do this - or if it's even possible.
Is there...
Good afternoon,
I had a question regarding scanning and pairing. Is it possible for a peripheral device to send scan requests after its been paired? or does the device have...
update SD+BL+APP from sdk12.2.0 to sdk14.2.0 , hang at trying to reconnect after loading the 1st image out of 2 on NRF52832. need reboot iphone and DFU application only to...
Hello,
I made a PCB of the nRF51822 chip and tried to program it with a simple led toggle code, but am not able to see any output, I am trying to figure out what is wrong...
In `nrf_log_backend_uart.c` there is a reference to `./integration/nrfx/legacy/nrf_drv_uart.h`. I'm upgrading the system to use the Nordic provided backend, but it would be...
