I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hello
We are using custom board which has two chip configuration for BLE stack. Main MCU runs the Zephyr Host only BT stack in peripheral mode.This is supposed to be GATT...
I am trying to compile the SPI example in SDK 15.2.0 for nrf52810. I am getting a compiler error in SES on nrfx_uart.c:
I modified the project according to the SDK documentation...
Dear all,
Is this possible to flip a switch on the board to get nRF9160 IOs at 3.3v rather than 1.8v ? I have a LoRa module that requires TTL 3.3v UART signals, and it...
Hello,
I believe I have found a possible race condition in experimental_task_manager / task_manager.c, task_events_wait().
The race occurs if a task calls task_events_wait...
Hello, I'm working with an example of ble_app_uart with SofDev132. I have modified the code a bit but I still use the nrf_pwr_mgmt_run function. The power consumption is 2...
hello, i am complete beginner to this field of MCU, i never worked on nordic MCUs. i am able to program the dk-board using the usb cable and readymade hex file provided in...
Hi,
I'd like to enable paring/bonding for a minute only when a button is pressed. So I need to disable pairing. I've learned that it should be done with
in "ble_evt_handler...
Hi,
I would like to have two different twi managers. One with TWI0 and one with TWI1. But if I try to enable them I get an error:
sdk_config.h:1810:22: error: unable to...
Hello,
I am new to BLE and trying to understand basic concepts.
Connection interval ranges from 7.5ms to 4sec. Device is doing Frequency hopping on all channels from...
Dear developers,
i now use the PPK intensively. I would like to have an additional feature. So far the trigger reacts only to exceeding a level. Would it be possible to...
I have developed CyclingPower SIG service based on (a) CSCS example and on (b) old file found here, at Devzone.
It used to work, but then something happened and I can't...
Hello.
I have been working with the nrf525840 dongle using SDK 15.2.0 trying to build a UART Service. I used the ble_app_uart example project that comes with the SDK and...
Hello everyone, I want to know and how, if it is possible, to hide UUID Beacon string during the advertising mode.
My goal is to not show the UUID by any sniffer, like Master...
Dear All,
I‘m going nuts while working on the basically really simpe task of reading ADC voltages on GPIO (AIN3) between 0 and 1.25V.
The voltage should fit well in...
Hi all,
At Peripheral end, I will get an callback "BLE_GATTS_EVT_WRITE" whenever I do a write on charcteristic write value from Mobile App.
Can you please point me to...
