Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi,
To build the context: I have two peripherals, Sensor 1 and Sensor 2. Sensor 1 has been running off of a NUS service to transmit data. Sensor 2 has been running off of...
Hi all,
I make a key using nrf52832. It tranfer data to other device. I have 2 option for this. Using beacon (BLE) or Enhanced ShockBurst (ESB) . I want to optimize energy...
Hi all.
In our project we are using BLE, but at some point switch to ESB. The code below disables the SD, and sets up ESB which is then used from then on.
This all...
Hi,
I am using nRF52 DK PCA10040 to develop an application starting from the ble_app_uart example, Then I introduced PWM and SAADC from other examples, and after I verified...
I have an nRF91 DK v0.7.0 which I'm using for the first time with a Hologram.io SIM card and nothing seems to be working. Nordic sales and an FAE were here in late February...
Hello,
I need to get nrf9160 to connect to a LTE-M network. We are using a custom pcb module with nrf91 on it. I've managed to get a simple hello world, blinky and gps simulator...
Hi,
I am currently working on a project in Mesh on nRF52840 DK.
I am using the mesh v3.1.0.
I wanted to send command from mobile app to particular node in the mesh and...
Hi, i use the saadc example(triggered by ppi+timer) with uart to get voltage signal and transmit to central device( another custom nrf52832 board), and the central prints...
I am using SPI communication to transfer data from an ADC (ADS1220) to my nrf52382, then to the mobile app via bluetooth. The ADC is the slave. The NRF is the master. So MISO...
Hi,
I am trying to read data via an ADC through SPI and send it via Bluetooth to the NRF mobile app. I checked that both the original BLE_UART example and the SPI master...
My SPI data transfer from a peripheral ADC works fine in the SPI example project. The same code doesn't transfer data properly when it is added in either a ble_template or...
Does the BLE NUS service use pins on the NRF? I'm using a custom made nrf52382 pcb where I transfer data from an ADC (ADS1220) via bluetooth to the nrf Toolbox app. But using...
static const nrf_drv_twi_t m_twi = NRF_DRV_TWI_INSTANCE(TWI_INSTANCE_ID);
Hi Everyone,
I'm new to nRF52832 programming. I want to learn more about nRF52 programs.
...
In SDK 15.2 is the nrf_cli module completely thread safe? I was thinking of developing a wrapper to use the CLI module for both application logging as well as a general CLI...
