Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I have a custom profile containing five custom characteristics.
The largest characteristic is 256 bytes in size and can be read reliably by an iPhone.
When it is sent...
Hi, there is a code comment "Workaround for PAN_028 rev1.1 anomaly 22 - System" in nRF5_SDK_12.3.0_d7731ad\examples\proprietary_rf\esb_low_power_ptx\pca10028\blank. So, I...
I would like to do I2C BlockRead using nRF52.
devzone.nordicsemi.com/.../i2c-block-read When I looked at it, I found that it was not possible to receive variable length...
Project migrated to SDK 15.3.0 with Softdevice S340 6.1.1
Project is using DFU secure bootloader. The example in "dfu/secure_bootloader/pca10056_ble" was used as the starting...
Dear nordic,
I have some doubts regarding PWM. i want two PWM out both are working different frequency and also i need softdevice. I think PWM can make two ways one is using...
Hello,
I want to change the 16-bit of 128-bit UUID at runtime. is this possible?
let me explain...
1)the first both central and peripheral set 128-bit UUID like this...
Hi,
Actually i m new on this field.
I m making indoor navigation by using nrf52840 soc.And i m using sdk15.2.In that sdk i used beacon app code for advertising beacon...
Hi.
I use a modified lightswitch server application with Nordic SDK 15.2, Mesh SDK 3.1.0 and Softdevice 6.1.1.
During provisioning I experience a software assert with...
Hi,
I want the bit rate to be 125Kbit or 500kbit. The project uses 1Mbit and 2Mbit. I'm investigating the topic on the Devzone blog. I reviewed the example nrf52840-long...
My work need to use 4 gpio interrupt, but it not work when use freertos on nRF52832 ,sdk version 15.0.0. My code is like below:
err_code = nrf_drv_gpiote_init();
nrf_drv_gpiote_in_config_t...
I created own app button library. It's just return handler into main with number of pin and type of push - short or long. Also I created library for rgb_led (using nrf_pwm...
Hello everybody,
I'm using nRF5280 (Laird BL654) with SoftDeveice S140v6.1.0 and SDK 15.2.0 with a modified version of the blinky peripheral example.
I've changed NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
Hello
Our custom board has two chip configurations for BLE stack. The two chips communicate with each other through UART. Both chips are running zephyr with two chip configuration...
