Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hello everyone,
I've got an issue with ESB. I'm using 3 nRFs 52840 with firmware based on SDK 15.2. One of them, the radio-receiver is RX, and two of them, PilotA and...
Hi,
I'm working on putting our system into low power idle mode. We use MyNewt to build our application. In order to get to the lowest power, I disabled BLE and all our drivers...
SDK 15.2, S132 6.1, nRF52832
I have a characteristics to write data to a peripheral, using variable length up to 507 bytes and authorization.
Writing to the peripheral...
I'm trying to get the code below to compile. One question is how to fill in the nrf_crypto_hash_info_t structure. Another issue is that the nrf crypto includes don't compile...
Chip: nrf52840
Platform: Android
MacOS Dev
There is pretty much no error logs but it can't actually send anything over mesh network on udp. Seems to receive without...
I have a RedBear BLE Nano v2 (nrf52832) connected to 3 AA batteries for power. I also have a Maxbotix (MB1043) ultrasonic sensor attached. I have configured a gpio pin for...
Hi, I am a beginner to nrf24le1. My company has products made of nef24le1. I would like to debug nrf24le1 devices but couldnt able to , I would like to know the answers for...
Hi. I am trying to run the makefile of ble_app_blinky (from SDK 15.2.0) on Ubuntu 18.04 and Visual Studio Code. When running "make" in the armgcc directory, the following...
i have recently upgraded to SDK 15.2, and since doing so I am struggling to get timestamps working in the logger.
I am initialising the logger here:
And here is my microsecond...
Hi all,
I've just downloaded SDK 15.2.0 on Windows 10 and it was unable to unzip the file and reported an error. I copied the file to Mac OS and got the same error.
Is...
Hi ,all.
I now need a open bootload through BLE.But I found it hard to modify it from the secure ble bootload example。
Any open bootload examples of 52832 through BLE...
Hi,
I try the last days very often to Recover my NRF52 Chips on NRFGO Studio 1.21.2.10.
Error: Unable to find or open the JLinkARM dll, Unknown Error.
I reinstall...
Hi,
I am developing a timing critical application for the nRF52840's and would like to implement USB functionality as well as be able to turn it on and off in software....
Hi,
Recently, I bought a nRF 52 DK in order to use it as sniffer for a project that evolves a BLE Mesh environment composed by multiple nRF52832. Although, I've not been...
Specs: SDK 14.1, nRF52832, S132
Env: Eclipse IDE, Linux
Hardware: Custom board
As the title explains, we've had no issues during development if the optimizations are...
