Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi,
I'm writing a client which does the OTA DFU for the nRF52832 and I'm a bit confused why the packet characteristic has the writeWithoutResponse property ( https://infocenter...
Hi, I have 2 questions regarding Nrf52840's zigbee connectivity.
1. Is it compatible with ALL other chip manufacturers, or at least, what about TI? CC2530? Zigbee has...
Dear all,
I am testing the light_switch demo (SDK for Mesh v2.0.1 and softdevice 6.0.0) below the following configuration:
-- One client: nrf52-PCA10040 DK (light_switch_client_nrf52832_xxAA_s132...
I read in a CMakeList.txt, that EXPERIMENTAL_INSTABURST_ENABLED is posible on the nRF52832 platform only.
Is it possible to get Instaburst running on a nRF52840 chip using...
I would like to separate the BLE communication from the main.c and place it to a separate file. I followed the example of the default ble_app_template as well as nordic's...
Hello,
Configure the nRF52832 (PCA10040) as suggested in the link below:
github.com/.../Android-Image-Transfer-Demo
Launched the Android Image Transfer Demo and we were...
Hi, i am working on a message model based on the simple_on_off model. I am able to send and receive a buffer via unicast or multicast. Now i am trying to develop a reliable...
I need help to build a demo of product consisting of BLE observer. I chose the nRF51822 due to lower cost, many choices for modules, and it does just what I need. I was able...
Hello System: Windows 10 Pro 64bit, 1703 I prepare the Toolchain on Win10 for BLE Mesh 2.0.1 SDK. During compilation of "pc-nrfutil-mesh_dfu" i get the error "missing NETAPI32...
Hi Nordic team
I compile the example ble_app_interactive in keil ver.5.24.
And the below error message occur.
I have compiled other examples and it works fine. (except...
Hi
I am designing Circuit with nRF4122 - QFN package 48 pin, as per datasheet there is circuit for Trace/ PCB Antenna
But i am planning to use Chip Antenna and BAL-NRF02D3...
Hi,
I have a custom board someone designed with two SPI masters and one I2C master. We're now trying to enable the second SPI master and I'm running into errors because...
Hi all,
I am working on FOTA, my set up is with SDK15. I have followed the steps for DFU and i have used the secure_bootloader example, the thing is working fine, i can...
hi i have attached my gps+gsm module with nrf51 development kit and while reading an out put i wont be able to see any output , even with out put i dont know to to do debugging...
