Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
When I input the command below:
nrfgocli -p <path_to_application.hex>
it gives me the error below:
Could not connect to board
ERROR: Could not connect to board ...
I've migrated over my application code. I've noted that SDK10's new modules causes much high RAM consumption than on SDK 6.1. Everything is working however, except for the...
What are the correct parameters that I need to set in uVision to compile the experimental (signing) DFU for NRF51822_xxAC (SDK 10) (using dual bank)
Xtal?
IROM1?
IRAM1...
Hi Nordic Community,
Could you please tell me what is the antenna reference design used in the nRF51 DK? and why a lot of BLE development boards (like Redbear BLE shield...
Hi everybody!
Im trying to implement slave spi to bluetooth bridge.
In short, when cs line goes low, i want that one handshake line automaticaly go in busy (high) state...
Hi,
I'm using the nrf52 and in my application I need to sample a sensor after applying an IR pulse; the pulse length influences the sampling thus cannot be disturbed by...
I think this is a rather common problem:
I want to expose a couple of variables from my model code (members of structs) as characteristics. Is there a simple and elegant...
Hi
Question
What is the risk/chance that future revisions (>2.0.0) of S130 will be incompatible with the setting UICR.CLENR0 = 0x1C000 ?
Background
Today we would...
Hi,
I need to wait for a period of 7.5ms whilst my I2C sensor completes a measurement, I am currently using the nrf_delay_ms function however I am looking to optimise the...
Hi
I'm trying to explore the nRF52-DK kit.
I downloaded the demo : www.nordicsemi.com/.../heart_rate_demo.zip
Dragged and dropped the hex-file to the JLINK drive thats...
Hello,
I am utilizing an accelerometer sensor and communicating with it using TWI (I2C). I have both a development kit (NRF51-DK) and the Beacon (nRF51822-Beacon). I can...
Hi all:
Below is my source code for SPI master.
However, the handler is not triggered ...
Is any setting I missed?
Thanks...
void spi_event_handler(nrf_drv_spi_evt_t...
Hi,
I am using nRF51822 BLE nano with mbed IDE. I tried to set channel so that i can achieve the desired frequency for FCC testing i.e. 2402MHz,2441MHz and 2480MHz .I am...
I am looking at the ble_app_hrs_c example (with the s130 soft device on pca10028 dev board). I have set the m_scan_mode to BLE_WHITELIST_SCAN to enable whitelisting. In the...
