Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi All,
I am using ' NRF SDK v2.7 + NRF5340 DK + VSCode ' and cloned a official nrf ' blinky ' sample. The code and pins are working fine and I have verified using DK...
Hello,
I can retrieve the data from the Thingy:53 via the bme68x_iaq program. However, I don't know and I can't read the data via BLE on my phone via nRF Connect. Do you...
Hi everyone,
I'm encountering a usage fault on the nRF52840 Featherboard when trying to connect to a network using OpenThread. The issue arises specifically during the execution...
Hi,
I am using the Create a new board function to specify a simple nRF52840 based board with GPIOs using nRF Connect SDK v2.8.0. No matter how I answer the questions in...
I'm using the nRF21540 DK with the Power Profiler Kit II in ampere mode for measuring current draw. I had the gain set to +20 dBm for testing but I noticed the system was...
Hi,
We have five NRF5340DKs with us and off late it seems three of them does not get detected by the PC. In fact, what i understand is that the interface MCU seems to be...
Thingy:91X rev 1.0.0
NCS 2.6.2 own custom application
Quiescent current measured with PPK II and extension board:
nRF53x 2µA, OK
nRF70x 0µA, OK
nRF91x 17µA, OK ...
Hello,
We are in the feasibility phase of updating a product to include a nRF9151 modem connected to a nRF52840 via a single UART. The modem will operate in SLM (Serial...
Hi,
Today the nRF Connect extension isn't working anymore: it doesn't show or let me select an SDK or toolchain.
I have tried on 2 separate computers where it was still...
I am using the latest (I believe) nRF Connect for VS Code extension, version 2024.12.55. But when I "Create a new application" and pick the ncs-example-application, it only...
Our nRF5340 application requires a lot of serial ports, but 2 of them are only used for a second during configuration and are otherwise (99.9% of the time) idle. If we could...
I am a complete newby to Nordic parts and the VB design environment so please bear with my ignorance. I have just purchased a nrf52840 development kit and have successfully...
Hello,
in an earlier entry I was asking about getting multiple BIS streams, where you led me to the nRF Auraconfig Sample.
I am now using this sample and got it to run...
I'm in the process of migrating my project from NCS 2.6.1 to 2.8.0.
My project consists of a BLE application with MCUBoot as the only boot loader.
I've already updated...
hello,
I Have two nRF52833 that I have communicating over BLE. I am using soft device S140. I have my data packets use the default data length maximum of 20 bytes. I am...
