Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
Dear Nordic team,
we are evaluating the nRF9151 for a data acquisition application/device. Our first goal was to get the official HTTPS client sample to run on the nRF9151DK...
Hi ... have code that outputs I2S in master mode. The slave, a NAU8822 device requires Master Clock Source between 8 and 33MHz.
The 54L MCLK pin is duplicating the BCLK...
To use the nRF54L15 SPI00 and SDHC, I have to edit the SDHC file and add board-specific configurations to start at a 1 MHz clock, since the SDHC file defaults to a lower frequency...
Hello,
I was going through "Bluetooth Low Energy Fundamentals" https://academy.nordicsemi.com/courses/bluetooth-low-energy-fundamentals/ .
I feel few need to be corrected...
Does Nordic make available 3d models (.stp files) for the nrf7002, nrf5340, and/or npm1300 chip scale parts?
The only information I can find on this is in a forum post...
Problem After successfully establishing a nRF7002EK WiFi connection to the local network, AWS IOT connection fails with “mqtt_helper: mqtt_connect, error: -2” and reboots...
Problem When attempting to flash a nRF board that uses pyocd as the runner (defined in devices’s baord.cmake) for flashing, the following error occurs.
It doesn’t matter...
Hi Nordic team,
I am currently researching Bluetooth Channel Sounding, where I have setup two nrf54LM20-DK as intiaitor and reflector respectively.
I am using NCS 3.3...
I'm developing a custom BLE sensor on an nRF52832 (E73-2G4M04S1B module, SoftDevice S132 7.2.0) with a companion Android app. On Xiaomi/HyperOS devices (confirmed on this...
Just purchased the PPK 2 Did the quickstart up and got this a message saying it's not yet supported. I am running Ubuntu Linux :
Distributor ID: Ubuntu Description: Ubuntu...
Your application for SUPL-C license has been denied.
Please make sure you have an active/approved DevZone account
You must apply using the same email address as for...
Hello,
I am using nrf5340 audio sample with the custom board. The nRF Connect SDK version I used is v3.4.0.
I added the following settings to prj.conf so that the custom...
Hi all,
the nRF54L15 hardware can support an external RF antenna switch. I don't see any hardware limitations (the switch could be controlled via GPIO), but the more interesting...
We are using the nRF9160 with firmware 1.3.6 to establish a DTLS connection to a server, using the Zephyr TLS stack.
The following problem occurs quite frequently: After...
Hi, I am fighting with a bug I found in SDK v2.8.0 for BLE scan filter on a test project as follows: 2 Devices (Ezurio BL653-DVK using the nRF52833), both having central and...
