I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
When we test the matter, we sometimes will meet commissioning accessory fail and network dropping. In the worst case, we can't access the network for a long time after the...
NRF_SO_RAI_NO_DATA AT#XSOCKETOPT=1,50 does not cause RRC release as expected, instead hipower LTE continues another ~20s. https://github.com/nrfconnect/sdk-nrfxlib/blob/main...
nRF52840, SDK 17.0.2, SD140 v7.0.1
My firmware application is happily sleeping via calls to nrf_pwr_mgmt_run(), waking up to service interrupts and do work, then going...
I have not been able to get the nRF52840 ncs v2.0.2 watchdog not to reset.
I tried kicking the watchdog every second and can set a break point and see that the kick does...
Hi all,
I'm looking for an SDK function that will tell me if my device is connected to BLE
from this post 8 years ago the answer is no, has something changed in those...
I am using the 9160 to develop a product for the customer. Its sdk version is ncs1.9.0, and the firmware version of the modem is v1.3.1. The device needs to download data...
Since sensor.h API in Zephyr does not support reading hw FIFO, I am planning to use SPI driver to read the hw FIFO on received an interrupt when FIFO has data.
Is there...
Hello
I use nRF9160DK.
Can somebody tell me why it doesn't give an error ( ) if I don't have anything on the I2C line, or how can I be sure if it finds the right address...
I've tested the TX power of nRF52840DKs using CLI application and a sniffer (sniffer device is nRF52840 Dongle). Sent message from one DK to other one via UDP and observed...
Hello,
I am trying to implement the Y-modem protocol to the ble_app_uart example. Basically, I want to send a file from the PC and receive a file in my nrf522840 device...
I use SDK16 with softdevice. Some of its features require hard timings. But it causes hardfault sometimes. It happened at function of gcm_init. My source code is as follows...
Hi
Is there any software that allows to save received Bluetooth data to a spreadsheet? I am using the nrf52 DK running the ble peripheral uart example and received the data...
Hello, after upgrading to SDK version 2.1.0 I noticed that the compilation of all my projects for actinius_icarus_ns always fails:
This is even for projects, where...
Is there a way to initialise a GPIO earlier than in main() without modifying NCS/zephyr code?
We tried an PRE_KERNEL_1 init() function, but this is rather late still.
...
I have two central devices and two peripheral devices each paired with two different services.
I wish each pair can connect only to each other and don't mix up the connection...
