I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
I'm currently working with a BL5340PA module with the external antenna connector. we were wondering what was the RF switch isolation between the two antenna outputs. In other...
Hello,
I am currently working on a project using a custom board with nRF52840 + nRF21540 . I am trying to measure wireless performance using Direct Test Mode (DTM) , but...
Hi, when I use OTBR to commission a matter bulb(52840DK), I found this log:
I: 7371 [DL]CHIPoBLE connection established (ConnId: 0x00, GATT MTU: 247) D: 7448 [DL]Indication...
Hi,
I have been trying to use the radio_test example application to try and accomplish my goal but no success so far. My goal is to be able to compose an advertisement packet...
Hello, we would like to use the 4th reference circuit with the QIAA footprint from the Nordic nRF52840 chip's datasheet. However, in our PCB design, can we change the placement...
Hello,
I'm attempting to write to a ble characteristic but when i call bt_gatt_write, I get BT_ATT_ERR_INVALID_ATTRIBUTE_LEN, I have tried to send the same command using...
Question: I am working with the Ebyte E73-2G4M08S1C module, which is based on the nRF52840 . The module provides D+ and D- lines . Can these lines be used for debugging and...
Hello,
I'm trying to put the nRF54L15DK into System Off mode, using sdk & toolchain version v2.8.0.
The provided example (\samples\nfc\system_off) works on my evaluation...
Hello Team, We are currently building a circuit using nRF52833 QDAA QFN40 ( Configuration 5). We would like to know if there are dedicated pins to be configured for BOOT as...
Hi everyone,
I'm working on a Matter based project on the NRF52840 SoC. Since it's an Iot project project we need to reduce power consumption at it's minium for lifetime...
We're starting new medical research project where we have to send data at rate of around 4Mbps from the sensor array for a distance (omnidirectional) of around 2 meters. The...
Good day,
I am learning how to program NRF52832 chips using the NRF52 DK. I am using Segger embeddded v8.2 for the moment as I have not yet learnt how to use the NRF Connect...
Hi,
We have a project based on NRF52811_xxAA_REV1 running on multiple devices without any problem.
Nordic announced recently newer version of SoC (REV2, aka B0) and since...
