Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi.
We've created a custom board, and it works nicely.
However, when I try to build another application for this new board (i.e. "Add Build Configuration"), the new board...
Hi,
I'm using the nRF Connect app on android to DFU my devices.
On some occasions, after doing DFU and unbonding, the phone will keep asking if I want to pair the device...
The Absolute Maximum rating of I/O pin voltage for VI/O, VDD ≤3.6 V is -0.3V to VDD + 0.3V in Table 185. We would like to monitor the battery voltage using an AIN pin because...
Hi, We are using the SDK v17.1.0 and SD S140 v7.2.0. In our application we have to send only 1 advertising packet with updated data every 300ms and in some cases every 50ms...
Hi,
I work with win10 laptop, Toolchain nrf Connect SDK 1.6.1 on a nrf5340dk.
I modifyed peripheral_uart to use 240 bytes like it's explain into "ncs 1.6.1 peripheral_uart...
Hi, I am trying to create a custom BLE service.
Following is the main code:
These are my BLE write functions:
My sdk_config file says MAX_MTU is defined 23
...
Hello everyone,
I have a few questions related to NFC in nrf52832.
1. UUID in nrf52832 NFC is Unique?
2. Can I use nrf52832 NFC for payment purposes..? if yes How I...
Hello sir,
I am using nrf52832 soc with customised board want to use as UART pins as RX pins as 23 and TX pins as 24 .Is it possible to use the RX pins as 23 and Tx pins...
Hello,
I am trying to configure a Zigbee coordinator as done in the CLI example (for example 'bdb role zc' and 'bdb start') to get data from the multi sensor example,...
Hello,
Lately we've had some problems with DFU using the NRF connect app.
The device we are using is a nrf52832 running Zephyr 2.6 with MCUBoot 1.8
When we set the following...
Hi,
Turning on A-GPS (using the SUPL library) causes our application to encounter a boot panic ("unable to find bootable image"). Similarly, running the nRF9160 GPS example...
Hi Dev team,
I have been working with the MQTT example and building up my application. I establish a successful connection with the broker and everything runs fine for 5...
I had trouble connecting the device to the computer. My computer shows that it is connected, however, in VS code, it cannot find the device. Also, when I tried to use the...
