Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
hello Nordic
i work with nrf52840, SDK16.0 S140
i use QSPI for writing to an external flash (IS25LP064A)
if i write 16 bytes then its all ok but if i try to write...
Hello,
I have nrf52810 with soft device S132 5.1, SDK 14.2.
It works fine when NRF_LOG_ENABLED is enabled, data from NUS are printed in debug console. But Im not able...
Hello,
I am writing a BLE central application that connects to a device and should then discover ALL services on the device. I am new to Nordic and am using the nRF5340...
Hi
I am going to start an application with the mesh network. Here is my requirement,
1. I have to receive the data from the master device (STM32) by using SPIS (nRF52840...
Hello,
I am using the ble_app_uart_c_pca10056_s140 example code (SDK v17). This is the NUS BLE central device.
The code is almost unchanged from the example source.
...
I'm quite new to nrf.
These days I'm trying to program power efficient uart data sender over ble.
It receives uart and sends data fine.
The problem is it's not going...
Hello,
Does nRF52833 has support for FreeRTOS in version 16.0.0 of nrF SDK?
Is there any specific example with the softdevice and FreeRTOS?
Thank You,
Vineeth...
When we develop out product, we found it cannot connect to our server. After our check step by step, we found if we comment the code about RAI setting, MQTT service can be...
I wanted to add TWI functionality to the flash fds example and was confused about adding drivers with CMSISwizard. I manually added all the necessary twi drivers based off...
HI
I have got a new nrf5340 DK. I have tested four LEDs and HRM. It's working fine. But when I have tried to upload blinky or hello_world Sample from NCS v1.5.1, I can't...
Hi all,
I have tested successfully the wireless timer syncronization proposed by:
https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts...
Hello guys.
I recently discovered that you included example codes for OSDP Control Panel (CP) and Peripheral Devices (PDs). In NCS v1.5.1 that I am using, they can be fund...
Hello,
I'm using the Infineon Optiga Trust X chip for ECDSA signature verification but I'm having trouble saving the public key.
Currently the public key is generated...
C++ exceptions can sometimes fail causing a std::terminate on every throw. This turns out to be a linker issue present in the following files:
nRF5_SDK_17.0.2/components...
