Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello All,
I am looking to use the nRF52840 for a ZigBee project. I am looking at the ZigBee light bulb example and following a few posts here I got it building. I can...
Hello,
I get the following errors when trying to DFU using a nRF52832 DK and the nRF Connect desktop application.
19:00:36.143
Attribute value changed, handle: 0x0F...
I want to build on the agps sample for 9160-dk
This involves changing the destination and format of outputs to cloud
I saw that multiple GPS hits are consolidated and...
Hi, Dear Nordic & all:
when I prepare to do a DFU example，I get trouble in installing "nrfutil" tool
I sure that I installed it successfully， but when I input "nrfutil...
Hi
I have a nrf52840 dongle with which already been flashed with ot-NCP binary and I want to over write this binary with new binary image[ot-rcp] in nrf connect for desktop...
hello,
I'm working with nRF52840 dongle, i installed nRF Connect for desktop v3.6.1 on ubunto 18.4 and i am using python3. After programming connectivity_4.1.4_usb_with_s132_5...
Hello I'm using Zephyr and trying to update the characteristic value with interval of 50ms. The problem is that the android app nrf connect freezes after I start reading the...
Hi,
I'm trying to run the light_switch sample app from nRF SDK for Mesh.
I have both PCA10056 and PCA10059, and I used both to run some other applications before testing...
Hi. I'm evaluating the nRF52810 chip by developing on the nRF52-DK (based in nRF52832 chip). As noted in this chapter https://infocenter.nordicsemi.com/topic/sdk_nrf5_v17...
We need to work with the PWM, the idea is to set one frequency, duty 50%, and put out these pulses to one pin, we understand how to do that but we need to stop these pulses...
Hi,
I once got the following message while trying to attach a debugger to my network core.
After this event, I haven't been able to program my network core.
I have...
I am looking at the hardware design of Thingy91, where the antenna is shared by LTE and GPS/GNSS. My system will be connected to a cloud (probably most of the time) and track...
Hi,
Our NRF52840 (running 14.2) often takes a very long time to disconnect, from when a disconnection is initiated by the phone. It can take 30s, sometimes even more, for...
