Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
I'm using nrf_pwr_mgmt_shutdown to shut down the system to wake on interrupt. 17.0.2 SDK and 7.2.0 softdevice. When I step through the code with a debugger, it gets to sd_power_system_off...
My device is powered by an electromagnetic field from the 10 kilovolt line, which cannot deliver much power. When connected to a zigbia network, nrf52840 consumes too much...
I want to receive only 1 byte (Master in Slave out) without sending any bytes using using SPI. However when I monitor the SPI clock it produces 16 clock pulses. Although my...
Hello, How do disable code optimization in SES Nordic Edition when using nRF Connect SDK? I can't find "Options - Code Generation - Optimization Level" as when using nRF5...
Dear Sir,
I am trying to run example with NRF91 DK MQTT simple and I am able to connect with LTE network. as shown in below screenshot.
But as shown in the screen...
Hello, All
I go through datasheet of nRF5284o QFN73 IC. But i can't found which pins are used as uart /spi/i2c/pwm/timer/ I2S in pin description. Because pin assignment...
Hi,
We are using nRF Connect SDK for implementing HSL model for the BLE Mesh network consisting of RGB lights.
On comparison with nRF Mesh SDK, we found that the SDK size...
Running the ADC in continuous mode, but it seems we still have to set NRF_SAADC->TASKS_SAMPLE in a while loop. Shouldn't this not have to be set? In continuous mode we shouldn...
Hello,
Currently, I am having a problem with my BLE application. I am using nRF5_SDK_17.0.2_d674dde version. The BLE can advertise and can be seen by my phone. When my phone...
Hi,
For nRF9160, configured for GPS plus LTE: What version of nRF Connect SDK supports GPS+LTE in eDRX mode? Also, are there any plans to provide modem support for GPS+LTE...
Hi, I am trying to test the uart exemple on nrf52840 using external debugging as shown in figure but it doesn't function !!!!
are there any modifications that need to be...
nRf Gurus, I need your help! It is very hard for me to understand top level configuration of the soft devices and overall mentality. I am sure it will be very easy and convenient...
I want to create a 1MHz timer using TIMER2.
I try to start the timer with the following settings, but the device probably hangs.
I also use app_timer, is it a problem...
Hello, Not so long ago I asked this question and the solution I was given is still working for the devices I was using. Now I've received a new version of the device in which...
Hello,
I am using nRF52832 DK module(for master), and breakout board(for slaves, 4-slaves).
I have some problem while BLE communication.
First, I am wondering if I can...
