Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
Based on zigbee sdk 4.1, in the sample code of light_switch, leaving the network and joining the network are completed by buttons, the code is as follows:
Seen from the...
Hi, my BLE application on nRF52832 is designed to select two mode to operate with 3 position slide switch when power on like ON(Mode 1) - OFF - ON(Mode 2).
At Mode 1 position...
Hello.
I'm using nrf52840 to sample the voltage from the wireless board and then send the data to the PC via Bluetooth.
With the help of DevZone, it was able to construct...
Hi,
I have downloaded and installed nRF Connect for desktop - Bluetooth Low Energy. Now I want it to operate as a peripheral that can send connectable advertising packets...
I'm having an odd issue with libUARTe sending a TX buffer twice.
I have a custom board using an nRF52832 running an application based on SDK 15.3.0. The libUARTe code was...
Doing development on nRF52 DK board using buttonless DFU example and SDK 17.0.2. Running SES on Win10 and gnu compiler.
I've set up a 1 mS timer to run timing in my main...
I am using the ble_app_uart in combination with the f_storage example to write data to the flash memory. A issue which arises is that, when a softdevice is enabled, the nrf_fstorage_nvmc...
I am using Mesh SDK v4.2.0 and my goal is to get the device MAC from the UUID that is available from p_evt->params.unprov.device_uuid available on the prov_evt_handler callback...
I guess this should be obvious, but I still have to ask. What do XRFTEST RX and TX modes actually do? I've read the documentation and it "feels" like they command the transceiver...
Hello
It seems that we had a crash during execution of nrf_bootloader_fw_activate() in an added sub function where we program an externally connected MCU and the bootloader...
Dear Sir,
I'm use 2 nrf52840 chips to test sensitivity by nRF-DTM-1.0 tool.
I find out it's work on 1M and 2M but S8 and S2 can work.
The PER can't get 0% when I only...
Hi all,
I am developing BLE firmware to send and receive data between the development kit PCA10100 and nRFConnect App Desktop.
I'd like to notify the client (the App)...
Hi all, I am using SPIM with dma list triggered by gpiote. A gpio low-to-high event starts spim reading, and it works fine. However, I need to read different length at different...
