I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hello,
We are currently developing with the nRF9151 and would like to request more information regarding GNSS SNR testing.
We have reviewed the documented GNSS functionality...
I have a similar question as posted here but I wonder if this limitation is still the case.
I am trying to advertise to a specific device by passing the scanner device's...
Hello all,
I´m Trying to Run the Minimal-Example of Sensor-Stream API
https://github.com/zephyrproject-rtos/zephyr/tree/main/samples/sensor/stream_drdy#id7
HW is:...
Hi All,
I have a ordred couple of 5340 Audio DKs. I want to configure one of them as headset using the nrf_audio example application and connect to a phone and stream...
I'm developing code to run on the nRF5340 SoC in a Thingy:91 X and I am seeing duplicate RTT output. For example, if I look at the RTT output from the default 'Connectivity...
Hello LE-Audio team,
By any chance, do you have a working code base that supports a headset with 2 end points instead of just one as your sample nRF5340_Audio kit?
If...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
I saw a really similar post but no real solution. I've got both a nrf52840dk and a fanstel ble840xe eval board that I've been playing with. the end goal is to make this start...
Hi,Team,
I am developing Pawr using nrf54l15-dk.
For the Pawr example I refer to E:\NCS\v2.8.0\zephyr\samples\bluetooth\periodic_adv_rsp and periodic_sync_rsp.
Regarding...
Hi everyone,
I'm new to Nordic development and currently working with a custom board based on the BC40C module (using an nRF5340). I’m facing an issue with the Bluetooth...
I’m working with nRF9151 + Toolchain 2.9.0 and wanted to share my experience & issue while sending ~7kB data over UART. I’ve tried both DMA & FIFO-based approaches — here...
I am designing a wireless sensor pcb with the nRF52840. I am essentially following the Circuit configuration no. 4 schematic for QIAA aQFN73 from the datasheet to a tee (schematic...
Hello,
I have bought a couple of Nordic NRF54L15 DKs, and it seems that the distance measurement toolbox that was compatible with the NRF52 series is not supported in...
