I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
I have successfully setup the build environment for SES using the NRF Connect Getting Started Guide. I verified operation of my board with the at_client and mqtt_simple projects...
Hi,
We are working on a project based on nrf51822. We have an application that needs to send 2 byte values to the mobile app every 200 milliseconds accurately(ideally 5...
Hello everyone,
I'm trying to communicate ble_app_uart and my customized mobile app(central) with static passkey my code as below
i facing problem when i make connection...
Hi,
Is it possible for me to manually flash the zephyr.bin on the nrf9160 located in proj/build/zephr/? I can flash the merge.hex however I do not want to use the merge...
I am investigating using a front-end module with a nRf52840 in an 802.15.4 application. I have seen the 802.15.4 stack in the nRF5_SDK_15.3.0_59ac345 SDK. It looks like there...
We have an application for using the 802.15.4 protocol with a nRf52840 and a Front End Module. We are looking for an approach to take for integrating the FEM control into...
Hi,
I'm trying to figure out if my device is suffering from errata 172.
* How can I know if I'm using Ble_LR125Kbit or Ble_LR500Kbit? * I'm trying to use the function...
To the kind attention of Nordic support team,
I would like to do a question that is not strictly related to Nordic, but I hope your expert can kindly give me an answer,...
Hello,
I am a student who tries to make a smart IoT project using nRF9160 DK and Arducam OV5642. I am searching on the internet to where to start, but I cannot find any...
If all you need is changing PHY, Tx power and Device Name in a standard nRF52840, do you need building a new bootloader from the scratch or the is a way to edit the standard...
Hello,
I'm experimenting with the nRF SDK for Mesh v3.2.0 and a nRF52832 DK, specific with the LPN example.
I want to enable BLE DFU support so I followed the instructions...
I am programming with SDK15.0. Then I use nRFgo studio to download the merged program to the DK board. But it reported a validation failure. So I tried to download softdevice...
I am building a project that is based on the custom service example https://github.com/bjornspockeli/custom_ble_service_example but I don't like how it advertises in a way...
