Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
Hi There,
I am working with the nRF52832 and one thing that the software team noticed is that the info.variant we get from the micro is not listed in the data sheet v1.4...
Dear sir,
The current BGA ball size is 0.3mm. What is the recommended VIA hole size for the inner pads for routing the signals out from IC ? or How large of the via in...
Dear Company,
I would like to ask about start-up time of this product nFR24L01
Max 1.5ms start-up from power down mode
Max 130us start-up from standby-I mode
1...
Hi, everyone
how to increase the peripheral link count in multi role lesc example . even i have tried with NRF_SDH_BLE_PERIPHERAL_LINK_COUNT by increasing the count, i am...
I have followed the dfu bootloader instructions for dfu secure ble example in both sdk 15.3 and 15.2 versions. I copied pca10056 folder to pca10059 and changed the board definitions...
Hi. I'm using nRF52832, SDK13.0.0.
I'm developing not only peripheral side but also central side.
I already made peripheral side referring to DFU example code.
But i...
I was trying to measure the current used by the nRF52840 on the DK. But it seems like i have messed up.
The debugger LED does not light up
The nRF52840 SOC seems to...
hi team,
i have downloaded image transfer demo source code in github. installed it in sdk 13.0. the softdevice is 5.0.0-2. i am using nrf52840 pdk. the code is successfully...
Hi Al
I'm implementing multiple channel ADC with PPI
sampling multiple ADC channels with PPI, adc event triggered adc_event_handler as many times as channels (instead...
Hello everyone. I'm working to a project with nRF52840. I'm developing the code in SDK in SES ide. The task i want to perform is transfer data from the memory of nRF52840...
Hi,
I am using the S130 central pairing to just one peripherial at a time. Upon power up after hard/soft reset, the central connects to my peripherial just fine, transfer...
Hello,
We are using the Segger Embedded Studio and trying to flash the blinky code on our nRF52DK. We have seen many videos but are unable to make it work. The code gets...
Hi,
In my memory usage, I see 780KB free from 1MB of flash. That means I am already consuming 244KB of flash when my code size is only 77KB. Obviously, there are other registers...
I have been trying to flash my nrf51822 by waveshare using my nrf 51 DK. I have been making the following connection. I am currently using P20 as the needle adapter for P19...
