Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi
i have an application where 3 SPI devices are connected. Each of the devices have a different CPHA/CPOL configuration. This means that, in order to make this work properly...
I am changing my project from 6.x to 7.x, and I saw in the BLE Bootloader/DFU documentation that there is a point in the bootloader where it decides weather to use the init...
I am having power on lock up issues with my latest product design using nRF51422.
There is no external power monitoring ICs or reset ICs.
The system is relied on internal...
hello everyone ,
Well first I have to mention that I'm at a the very starting stages in using this great DK and I went throw some tutorials ...
Well , I have some questions...
Hi,
I'm trying to set up a link between one master and 10~ slave devices. All I need is a lowest latency and little data rate for short time.
And there is my question...
I'm using nrfgo to program nrf24LE1, and want to use commandline programming. I've tried to find an overview of the commands with no luck. Where can I find it? I've tried...
Hi all
The release notes of the S130 V2.0.0 states that an updated SoftDevice Specification can be found at the infocenter. But there is only the specification of S130...
There are 31 io pins on nRF51822.
I use 8 io pins for our product. But I don't use the other pins.
All of io pins have the same default value after reset as follows. ...
Hi Guys
I have a noob question about the mesh network for nRF52832.
For devices to be inside a mesh network, does it mean that they need to do some kind of parring or...
I want to use pstorage with ble uart to store the data over bluetooth to flash . I did the coding for the pstorage operations. But the problem is that the pstorage store,...
I use a nrf51822 with the sdk 10.0.0 and s110 8.0.0. The nrf51822 have a peripheral role. The Connection interval min is set to 500ms, the Connection interval max to 1s, the...
My custom board, it connected with App, App sends a command to the board and the board keeps the command in the flash, but when i call the "pstorage_update", it will cause...
I want to use the FICR data on the nRF51 to figure out the RAM size. I found a problem and was wondering if this is a known issue, and if it's been fixed in newer revisions...
Hi Guys
I have a project where we are using nRF52832 chip. We need to make an app that can scan for beacons and give us "angle direction" to the nearest beacon.
The...
Hello, everyone. I used to use TWI with BLE in SDK 6.1.0 to operate ext sensor. Now I want to update my program in SDK 10.0.0. But there are too many differerance between...
