Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hey guys,
I’m trying to send a single non-connectable beacon every few minutes in the lowest power way possible. nRF51822, SD S110 8.0, SDK 9-2. Different scenario from...
I am experiencing a fault at sd_flash_page_erase() in the sdk_nrf51 ble examples.
Softdevice 8.0.0 is loaded and is from the sdk_nrf51 bundle.
Both the ble_app_proximity_s110_pca10028...
Here is my power consumption (3.0V):
no app_pwm: 0.010mA
after app_pwm_init(): 0.295mA
after app_pwm_enable(): 0.891mA
If I do app_pwm_uninit(), power consumption...
NRF52 on-site training for today, know BLE pairing use OOB way will be a little bit more simple and safe, and then want to ask next, on NRF51822 platform have the corresponding...
I'm using a dev board based on the nRF52832.
The majority of the time the RSSIsample register returns the correct value.
However sometimes the value returned is 0x7F...
The Product Specification makes it clear that the given levels of accuracy for ADC measurements are only possible when using an external crystal for the HFCLK. We have one...
Hi Nordic,
Running a gdb session on nRF51, it is difficult to debug the code beyond the SoftDevice initialization. Then, I have to step through with (gdb)ni, but this is...
Hello everybody,
I used to my PCA10028 DK board with nRF51-DK-mbed-IF but I wanted to revert for nRF51-DK-J-Link-IF. According to the nRF51-DK - User Guide v1_0 documentation...
I have the code below initializing TIMER1 and and IRQ every 1ms. I call app_sched_event_put within the timer and I get a Hardfault.
Any hints on what is going on ?
Thanks...
I just bought a nRF5-DK and I couldn't get it to work flashing other nrf51822s. The modules I'm using are these wireless-tag.com/.../nrf51822-02.aspx
Here's literally what...
I have a PCA10001 setup and I am using SDK v9. I have opened the UART example in CrossStudio.
It compiles/builds and I am debugging with breakpoints.
My question is...
Hello,
I use the interface I2C to communicate to the Light Sensor, and also use a timer to read the value back every 1 sec now.
I'm wondering that can I use the interface...
I use nrf51822 by example ble_peripheral/ble_app_uart with with SoftDevice 8.1.0, at the same time, I use pwm driver library, But it does not work well, What I need to do...
